<p><strong>When performing analyte extraction with </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products?category=136&amp;manufacturerItems=50"><strong>SPE</strong></a><strong> we expect 100% recovery. If recovery is lower, this would suggest there is an issue with retrieval of the analyte from the sorbent. But what are some of the reasons you may see a recovery greater than what you were expecting (or over 100%)?</strong></p><h3><strong>Common problems</strong></h3><ul><li>Co-eluting interferences</li><li>Contaminants from the solvent or sorbents selected</li><li>Internal standard is compromised making your reference point inaccurate</li><li>Recovery calculations are inaccurate</li></ul><p><strong>Let's examine each of these common problems.</strong></p><h4><strong>Co-eluting interferences</strong></h4><p>These are typically present in the matrix and the goal of the SPE step is to remove them. If you are experiencing recoveries greater than 100%, the first step would be to <strong>check the eluent using an orthogonal analytical technique </strong>to identify that the increased recovery is a result of a co-elution.&nbsp;</p><p><strong>Where a co-elution is identified, there are a few possible solutions.</strong></p><ol><li><strong>Modify the wash steps of the SPE method </strong>to selectively remove the impurity during washing</li><li><strong>Select an alternative SPE sorbent </strong>which will better remove these impurities. This is easier if the analyte / impurity can be selectively ionized, as an ion-exchange sorbent will very often afford cleaner extracts than either reversed or normal phase solutions</li><li><strong>Adjust your analytical method</strong> to resolve the 2 peaks analytically, negating the necessity to remove this impurity during the SPE step.</li><li><strong>Run a blank plasma sample</strong>; this will allow you to ascertain the impurities present and use this blank in the calculations to subtract from your recovery</li></ol><h4><strong>Contaminants from the solvent or sorbent</strong></h4><p>These will typically be impurities present in the starting materials which are similar in nature to your compound of interest, and as a result co-elute with it during SPE and subsequent analytical analysis. You can <strong>follow the steps above to remove co-eluting impurities, or alternatively</strong> as this is not an impurity present in your matrix, you can identify the level present in the sorbent using blank runs and subtract this from your main peak during the calculation. Prior to addition of your sample if you equilibrate your sorbent with the elution solvent this should flush out potential contaminants from the sorbent. For impurities introduced from the solvent, typically switching the solvent should resolve this.</p><h4><strong>Internal standard is compromised</strong></h4><p>If your internal standard is not showing 100% recovery, your subsequent calculations will be inaccurate. It is always good practice to <strong>use an internal standard similar in nature to your compound of interest</strong> as this will give the more consistent reference point for your method.&nbsp;</p><p>If there is concern your internal standard is not showing good recovery from the SPE material using your method, you can use an <strong>external standard</strong> which is added to the elution solvent to calculate absolute recovery.</p><h4><strong>Recovery calculations are inaccurate</strong></h4><p>It is important to follow this step wise to ascertain where the errors are appearing.</p><ol><li>Calculation Errors - Check all calculations and account for all dilution factors</li><li>Integration Errors - Reintegrate all peaks and use manual calculations to confirm</li><li>Analytical method errors – Ensure the analytical method used allows correct integration and calculation. Ensure no strong solvents are used for injection and run a calibration across a number of dilutions to ensure linearity. Troubleshoot your analytical method to determine any factors which may lead to poor reproducibility</li><li>Ensure detections selected are appropriate and working correctly.</li></ol><p>We hope this tip was useful! Check out our resources on <a target="_blank" rel="noopener noreferrer" href="https://www.phenomenex.com/techniques/solid-phase-extraction"><strong>solid phase extraction</strong></a>. See you next month for another tip!</p>

Why are my recoveries greater than 100%?

<div><div><p><strong>A new paper from the group of </strong><a target="_blank" rel="noopener noreferrer" href="https://curtis.group.uochb.cz/en"><strong>Ed Curti</strong></a><strong>s at IOCB Prague in collaboration with the </strong><a target="_blank" rel="noopener noreferrer" href="https://pluskal.group.uochb.cz/en"><strong>Pluskal group</strong></a><strong> introduces a structure-guided way to explore nucleic acid sequence space that goes far beyond traditional random mutagenesis. By combining rational library design, single-round selections, high-throughput sequencing, and machine learning, the authors rapidly identified catalytically active variants of a fluorescent deoxyribozyme and elucidated predictive rules linking sequence to function. The study was published in the journal </strong><i><strong>Nucleic Acids Research</strong></i><strong>.</strong></p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_2_2eb701e572.jpeg" alt="IOCB Prague: Exploring sequence space beyond random mutagenesis" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_2_2eb701e572.jpeg 245w," sizes="100vw" width="2006" height="789"></p></div></div><div><p>Understanding how sequence determines function remains a central challenge in nucleic acid engineering. Conventional strategies typically rely on libraries generated by random mutagenesis of a single variant of a motif, which provide dense coverage close to the original sequence but little information about more distant variants. This limitation makes it difficult to uncover more general principles governing complex functional motifs such as catalytic nucleic acids.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_e1e7a30d1c.jpg" alt="IOCB Prague/Tomáš Belloň: Edward Curtis, head of the Functional Potential of Nucleic Acids group at IOCB Prague" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_e1e7a30d1c.jpg 234w," sizes="100vw" width="1500" height="1001"></p><p>In a new study led by <strong>Edward A. Curtis</strong>, with <strong>Jaroslav Kurfürst</strong> and <strong>Martin Volek</strong> as the first authors, the researchers<strong> introduce a fundamentally different strategy</strong> for exploring sequence space that combines structure-informed library design, single-round selections, high-throughput sequencing, and machine learning. Instead of randomly mutating a single sequence, the team constructed a library composed of sequences that already satisfy multiple structural and functional constraints of a target motif. This approach was tested on Aurora, a fluorescent deoxyribozyme previously <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/article/4223"><strong>discovered</strong></a><strong> </strong>in the group.</p><p>The results indicate that this approach is a more efficient way to explore sequence space than standard approaches. A secondary structure library based on Aurora yielded approximately 40 times more unique catalytic sequences than a conventional randomly mutagenized library, and active variants could be rapidly identified in a single round of selection. High-throughput sequencing data were then used to train machine learning models, which successfully identified rules relating sequence to activity. Remarkably, these models could accurately predict read numbers and identify the most active variants using only small subsets of sequences for training.</p><p>By integrating rational library design with data-driven analysis, the study demonstrates a scalable way to explore nucleic acid sequence space more rapidly and comprehensively than standard methods allow. Beyond fluorescent deoxyribozymes, this framework provides a general blueprint for accelerating the discovery and optimization of functional nucleic acids, while simultaneously extracting predictive rules that link sequence to function.</p><blockquote><h5><strong>Read the paper</strong></h5><p>Kurfürst, J.; Volek, M.; Samusevich, R.; Pluskal, T.; Curtis, E. A. Using Structured Libraries, Selection, and Machine Learning to Rapidly Explore the Sequence Space of a Fluorescent Deoxyribozyme. <i>Nucleic Acids Res.</i> <strong>2025</strong>, 53 (22). <a target="_blank" rel="noopener noreferrer" href="https://doi.org/10.1093/nar/gkaf1348"><strong>https://doi.org/10.1093/nar/gkaf1348</strong></a></p></blockquote></div>

Exploring sequence space beyond random mutagenesis

<p><strong>Our Library never stops expanding. What are the most recent contributions to LabRulezLCMS Library in the week of 19th January 2026? Check out new documents from the field of liquid phase, especially HPLC and LC/MS techniques!</strong></p><blockquote><p><span style="font-size:20px;">👉 </span><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library"><span style="font-size:20px;"><strong>SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT LCMS AND RELATED TECHNIQUES</strong></span></a></p></blockquote><blockquote><p><strong>👉 Need info about different analytical techniques?</strong> Peek into <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library"><strong>LabRulezGCMS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library"><strong>LabRulezICPMS</strong></a> libraries.</p></blockquote><p>This week we bring you application notes by <strong>Agilent Technologies, Shimadzu, Waters Corporation </strong>and poster by<strong> Thermo Fisher Scientific!</strong></p><h3><strong>1. Agilent Technologies: Automated Bioprocess Monitoring with Agilent 1290 Infinity III Bio Online LC Solutions</strong></h3><p><strong>Process analytics of L-alanine production using genetically modified </strong><i><strong>Vibrio natriegens</strong></i></p><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_automated_bioprocess_monitoring_1290_infinity_bioonline_solutions_5994_8865en_agilent_9f33de6ddf.pdf"><strong>Full PDF for download</strong></a></li></ul><p>Bioprocess engineering is a challenging field because of the constantly changing nature of bioprocess models which make them difficult to validate.1 Consequently, process control needs to be developed at various levels using strategies tailored to these specific requirements.1 The performance and effectiveness of the bioreactor are determined by key performance indicators such as product yield, titer, production rate, and quality of the product.1 These factors can be quickly influenced by changes in process variables and the raw materials used.1,2 The ability to react quickly to problems is therefore crucial for preserving ongoing production, a factor that can be particularly significant in bioprocesses due to the substantial cost and time investmented.1,2 Such challenges can be tackled by constantly monitoring the bioprocess, which requires the ability to analyze and collect data quickly. Therefore, monitoring is of the utmost importance.&nbsp;</p><p>This application note describes the advantages of using an Agilent 1290 Infinity III Bio Online LC solution with Agilent Online LC Monitoring software. A bioreactor was interfaced with a Flownamics Seg-Flow S3 sampling system for aseptic withdrawal and an Agilent 1290 Infinity III Bio Online LC to make an hourly analysis.&nbsp;</p><p>This is a fully automated approach for taking sterile samples from a bioreactor and preparing or diluting them. In addition, the 1290 Infinity III Bio Online LC solution displays data in near real time, which is a crucial element for effective bioprocess&nbsp;monitoring.</p><h4><strong>Experimental&nbsp;</strong></h4><h5><strong>Equipment&nbsp;</strong></h5><p>The <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=10&amp;search=1290+Infinity+III+Bio"><strong>1290 Infinity III Bio </strong></a>Online LC comprised the following&nbsp;modules:&nbsp;</p><ul><li>Agilent 1290 Infinity III Bio Flexible Pump (G7131A) with an InfinityLab Quick Change Bio inline filter assembly (part&nbsp;number 5067-1607), 2.1 mm id, 0.2 µm pore size&nbsp;</li><li>Agilent 1290 Infinity III Bio Online Sample Manager (G3167B) with Sample Thermostat (option #101) clustered with Agilent 1290 Infinity Valve Drive (G1170A), featuring a reactor valve pod (part number 5067-6680) and Online LC Monitoring Software&nbsp;</li><li>Agilent 1290 Infinity III Multicolumn Thermostat (G7116B) equipped with an Agilent Quick Connect Bio Heat Exchanger Std. (G7116-60071)&nbsp;</li><li>Agilent 1290 Infinity III Diode Array Detector (DAD) (G7117B), equipped with a Bio Max-Light Cartridge Cell (G4212-6008), 10 mm, 1 µL&nbsp;</li><li>Agilent 1260 Infinity High-Performance Degasser (G4225A) is connected between S1 (transport solvent) solvent line and Agilent 1290 Infinity III Bio Online Sample Manager (G3167B)&nbsp;</li></ul><h5><strong>Software&nbsp;</strong></h5><ul><li>Agilent <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=10&amp;search=OpenLab+CDS"><strong>OpenLab CDS</strong></a> version 2.8 or later versions&nbsp;</li><li>Agilent Online LC Monitoring Software version 1.3 or later&nbsp;versions&nbsp;</li><li>Flownamics FlowWeb control&nbsp;software</li></ul><h5><strong>Instrumental configuration&nbsp;</strong></h5><p>The 1290 Infinity III Bio Online LC solution was used with a Seg-Flow interface for automatic sampling and online analysis (see Figure 1). The Seg-Flow interface was used to withdraw samples from a bioreactor through a Flownamics F-Series 310 FISP probe with a ceramic membrane filter (0.2&nbsp;µm pore size) from a 5 L bioreactor. The drawn samples were sent through the built-in sample collection cup on the Seg‑Flow to the LC and the samples were retained into vials. The collected samples were then automatically derivatized by using an injector program and subsequently analyzed. A more detailed description of the instrumental configuration has been published.<sup>3</sup></p><h4><strong>Conclusion&nbsp;</strong></h4><p>For online bioprocess monitoring, a fully automated setup consisting of a bioreactor, a Flownamics sampling system, and an Agilent 1290 Infinity III Bio Online LC solution was successfully established. This setup is capable of taking aseptic samples from a bioreactor, preparing, analyzing, and processing samples without the need for manual interaction. In addition, the added value of the Agilent Online LC Monitoring software was evident in the display method and the ability to track it quickly.</p><h3><strong>2. Shimadzu: Analysis of Oligonucleotide Impurities Using Single Quadrupole Mass Spectrometer</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_01_00974_en_c50bb67c7a.pdf"><strong>Full PDF for download</strong></a></li></ul><h4><strong>User Benefits</strong></h4><ul><li>Combination use of LCMS-2050 single quadrupole mass spectrometer and LabSolutions Insight Biologics provides comprehensive characterization of oligonucleotides and related impurities.</li><li>Purity calculations for target components can be performed even on poorly separated peaks by utilizing MS spectra simultaneously acquired with UV chromatogram.</li></ul><p>In recent years, oligonucleotide therapeutics have been paid attention as a novel drug discovery modality because of their rapid progress of development. During the synthesis of oligonucleotide therapeutics, impurities that have differing base chain lengths are generated along with the target oligonucleotide. To ensure the safety and efficacy of the drug, comprehensive detection and identification of these impurities are required.&nbsp;</p><p>Reversed phase ion-pair chromatography is often employed as a method to separate the target compound from co-existing impurities. However, it is often difficult to establish analytical conditions that provide compete separation of all impurities that are formed in synthesis process due to their similar structures and properties to the principal compound of active ingredient. Against this drawback, liquid chromatography-mass spectrometry (LC-MS) is commonly used for impurity detection and identification. For analysis of oligonucleotide impurities, quadrupole time-of-flight mass spectrometers are mainly used because of their high mass resolution and ability to perform sequence and structure estimations via MS/MS analysis. However, in quality control process, the use of a single quadrupole mass spectrometer is expected to be advantageous because of providing mass information with easy operation when impurity information is already known.&nbsp;</p><p>This article presents a simulated impurity analysis of synthetic oligonucleotide using the LCMS-2050 high-performance liquid chromatography-mass spectrometer and LabSolutions Insight Biologics.</p><h4><strong>Analytical conditions</strong></h4><p>The employed instrument setup was <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=1&amp;search=Nexera+XS"><strong>Nexera XS inert</strong></a> and <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=1&amp;search=LCMS-2050"><strong>LCMS-2050</strong></a>. HPLC conditions are shown in Table 2, and MS conditions are shown in Table 3. The conditions were set where n-1(5') co-eluted with FLP, while n-3(5') was separated (Fig. 1) to demonstrate impurity analysis performance.</p><h4><strong>Conclusion</strong></h4><p>The simulated sample consisting of mainly FLP and small amounts of n-1(5')/n-3(5') was analyzed using the LCMS-2050 and LabSolutions Insight Biologics software and obtained data were processed appropriately. Detection, identification, and quantitation at low concentrations were accomplished not only for n-3(5') well-separated from FLP but also for n-1(5') co-eluted with FLP. In case that establishing analytical conditions is difficult, Using this instrument setup and software will provide efficient quality confirmation of oligonucleotide therapeutics.</p><h3><strong>3. Thermo Fisher Scientific: Simultaneous Quantitation and Untargeted Discovery (SQUAD) workflow using multiple fragmentation techniques for quantitation and characterization of trace level nitrosamine in biological matrices</strong></h3><ul><li>Poster</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/po_squad_workflow_multiple_fragmentation_techniques_po_en_94a5b27b12.pdf"><strong>Full PDF for download</strong></a></li></ul><p>N-Nitrosamines are a class of carcinogenic chemical compounds that pose threat to humans exogenously through matrices like drinking water, food, cosmetics, and endogenously by nitrosation in gastrointestinal tract, nitrate to nitrite conversion, etc. An accurate, reliable analytical method is critical for detection and quantification of these trace-level, polar and low molecular weight compounds to understand the association between their exposure and related diseases.&nbsp;</p><p>An optimized SQUAD workflow is presented that discovers unknown compounds in the matrix by using high resolution orbitrap and a sensitive linear ion trap detector that quantifies the low intensity nitrosamines in a single run. The workflow uses multiple fragmentation types – HCD, CID and UVPD and MSn to help characterize isomeric structures.</p><h4><strong>Methods</strong></h4><p>Serial dilution of Nitrosamine standards were subjected to Simultaneous Quantitation and Discovery (SQUAD) analysis using <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/744"><strong>Thermo Scientific™ Vanquish™ Horizon UHPLC system</strong></a> and the <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/561"><strong>Thermo Scientific™ Orbitrap IQ-X™ Tribrid™ mass spectrometer</strong></a> . Nitrosamine spiked matrices of human pooled urine and human Serum were subjected to SQUAD analysis.</p><h4><strong>Data Analysis&nbsp;</strong></h4><p>Spectra were evaluated for nitrosamines using Thermo Scientific™ FreeStyle™ software and annotated using Thermo Scientific™ <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1757"><strong>Mass Frontier™ 8.0 software</strong></a>. Untargeted data analysis was performed using <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1759"><strong>Compound Discoverer 3.4 software</strong></a>. Calibration curves were generated using Thermo Scientific™ <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/77"><strong>TraceFinder™ 5.2 software</strong></a>.</p><h4><strong>Conclusions&nbsp;</strong></h4><ul><li>Detection limits as low ppb levels ( 0.2 ppb –0.5 ppb) and quantitation limits (0.2 ppb- 5 ppb ) in presence of the matrix were achieved for all seven nitrosamines by applying parallel ion trap analysis&nbsp;</li><li>SQUAD analysis was run on Orbitrap IQ-X Tribrid MS and achieved low ppb level quantitation in ion trap and identified unknown compounds through discovery analysis in Orbitrap.&nbsp;</li><li>Employing nano LC helped achieve lower limit of quantitation (5 ppt)</li></ul><h3><strong>4. Waters Corporation: Validated LC-MS/MS Method for Vitamin E Acetate in Cannabis Plants and Derived Products</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/720009082_en_c7a6fc6190.pdf"><strong>Full PDF for download</strong></a></li></ul><h5><strong>Benefits&nbsp;</strong></h5><ul><li>The validated LC-MS/MS method provides high sensitivity and specificity for VEA quantification in complex cannabis matrices, including flower and concentrates.&nbsp;</li><li>Minimal sample preparation reduces handling time and improves laboratory throughput, supporting efficient routine analysis.&nbsp;</li><li>The method demonstrates robust performance across multiple matrices, ensuring reliable detection even in lipid-rich, chemically diverse samples.</li><li>Use of Waters ACQUITY UPLC H-Class System and Xevo TQ-S micro Mass Spectrometer enables accurate quantitation well below regulatory requirements.&nbsp;</li><li>The validated method complies with Missouri DCR and DHSS regulatory limits, enabling laboratories to confidently monitor VEA in cannabis products.</li></ul><p>VEA is used as a diluent and viscosity modifier in certain cannabis-derived products, including vaping formulations. Following increased public health awareness during 2019, VEA became a marker of interest for quality control and regulatory surveillance across cannabis supply chains due to its potential impact on lung health. In addition to concentrates and vape liquids, trace residues may be present in infused products and processing intermediates. Therefore, reliable quantification of VEA in these chemically diverse, lipid-rich matrices requires an analytical method that is sensitive, selective, and robust against matrix effects. In February 2024, Missouri’s DCR revised the tolerance limit for VEA in cannabis products from 0.2 ppm to 5 ppm.<sup>1&nbsp;</sup></p><p>Liquid chromatography coupled with tandem quadrupole mass spectrometry (LC-MS/MS) provides the sensitivity and specificity required to distinguish VEA from endogenous cannabinoids, terpenes, and other lipophilic excipients, while also offering the sensitivity to support low-ppm and sub-ppm action limits. Unlike UVbased methods, where co-eluting chromophores may interfere, LC-MS/MS enables targeted multiple reaction monitoring (MRM) for confident identification and accurate quantitation in complex cannabis matrices.&nbsp;</p><p>This application note describes the validation of an LC-MS/MS method for the quantitation of VEA in two inhalable products, cannabis flower and cannabis concentrates. The method was developed and validated using the Waters ACQUITY UPLC H-Class System coupled with a Xevo TQ-S micro Triple Quadrupole Mass Spectrometer. Chromatographic separation was achieved with a reversed-phase ACQUITY UPLC BEH C18 Column. A streamlined sample preparation approach was applied for cannabis flowers and concentrates, which minimizes handling time and increases sample throughput.&nbsp;</p><p>The validation study was conducted at GPA. Method performance was evaluated for calibration range, linearity, LOD, LOQ, accuracy, precision, recovery, repeatability, and robustness. The results of these are evaluated against acceptance criteria set by State of Missouri DHSS and presented in this application note.</p><h4><strong>Experimental&nbsp;</strong></h4><ul><li><strong>LC system: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/198"><strong>ACQUITY UPLC H-Class Plus System&nbsp;</strong></a></li><li><strong>MS detection: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/209"><strong>Xevo TQ-S micro Mass Spectrometer&nbsp;</strong></a></li><li><strong>Column: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1952"><strong>ACQUITY UPLC BEH C18 Column</strong></a>, 2.1 x 50 mm, 1.7 µm (p/n: 186002350)</li><li><strong>Software:</strong> <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/635"><strong>MassLynx™ 4.1 Software&nbsp;</strong></a></li><li><strong>Data processing: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=5&amp;search=TargetLynx"><strong>TargetLynx™</strong></a> Application</li></ul><h4><strong>Conclusion&nbsp;</strong></h4><p>The LC-MS/MS method developed and validated for VEA quantification in cannabis flower and concentrates demonstrates excellent linearity, accuracy, precision, and robustness, and meets the regulatory requirements. Calibration curves achieved R² values greater than 0.999, with LOD and LOQ well below the Missouri action limit of 5 ppm. Matrix-spiked recoveries across flower and concentrate samples were within the 70–130% acceptance range, and QC samples met all performance criteria, confirming method reliability. Robustness testing across analysts and matrices further validated the method’s reproducibility. Overall, this approach provides a streamlined, sensitive, and regulatory-compliant workflow for laboratories, enabling accurate monitoring of VEA to support quality control, consumer safety, and regulatory compliance in cannabis-derived products</p>

News from LabRulezLCMS Library - Week 04, 2026

Article

Application

Academy

Scientific article

Science and research

Poster

The Institute of Organic Chemistry and Biochemistry of the Czech Academy of Sciences (IOCB Prague) is a leading scientific institution in the Czech Republic, recognized internationally. Its primary mission is basic research in the fields of chemical biology and medicinal chemistry, organic and material oriented chemistry, chemistry of natural compounds, biochemistry and molecular biology, physical chemistry, theoretical chemistry, and analytical chemistry. 

Institute of Organic Chemistry and Biochemistry of the Czech Academy of Sciences

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

Agilent 7100 Capillary Electrophoresis (CE) (G7100A) (Refurbished)

The Agilent 7100 Capillary Electrophoresis (CE) System in configuration with UV-Vis diode-array detector (DAD).

Bazaar products from category Capillary electrophoresis from Agilent Technologies - page 1

Related content

Exploring sequence space beyond random mutagenesis

News from LabRulezLCMS Library - Week 04, 2026

Why are my recoveries greater than 100%?