Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Application Note
Analysis of Oligonucleotide Impurities on the
BioAccord System with ACQUITY Premier
Catalin E. Doneanu,
Chris Knowles, Jonathan Fox, Emma Harry, Ying Qing Yu, Joseph Fredette, Weibin Chen
Waters Corporation
Abstract
This application note demonstrates an automated, compliance-ready LC-MS workflow for purity analysis and
intact mass confirmation of extensively modified oligonucleotides and their impurities.
Benefits
A category of products incorporating the MaxPeak High Performance Surfaces (HPS), including the ACQUITY
Premier UPLC BSM System and the ACQUITY Premier OST Columns, provide critical advantages for
oligonucleotide impurity analysis
■
An automated, compliance-ready workflow is shown to provide good mass accuracy (better than 15 ppm) for
intact mass confirmation of modified oligonucleotides and their impurities analyzed with an ion-pairing
reversed-phase (IP-RP) LC-MS assay
■
In addition, this automated, compliance-ready workflow provides purity information for all the sample
components, down to 0.2% abundance levels
■
Introduction
Oligonucleotide therapeutics have emerged in recent years as a powerful alternative to small molecule and
protein therapeutics.1,2 Manufacturing and quality control of oligonucleotide therapeutics requires highly
1
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
selective and sensitive LC-MS methods. One of the well-accepted mass spectrometry-based methods for
oligonucleotide analysis is ion-pairing reversed-phase chromatography (IP-RP) separation followed by ESI-MS
detection in negative ion mode. Using this method, an automated workflow for oligonucleotide analysis
employing the BioAccord System – operating under compliance-ready waters_connect data acquisition and
processing software – was recently described.3,4 A fully integrated LC-MS system comprised of an ACQUITY
Premier UPLC BSM System, a Tunable Ultraviolet (TUV) Detector, and an ESI-Tof ACQUITY RDa Mass Detector
(system shown in Figure 1) was used in this application note for the analysis of low-level oligonucleotide
impurities. This is a challenging analysis because oligonucleotides contain many negatively charged phosphate
groups prone to interact strongly with metal surfaces. To address these challenges, Waters has developed a
family of new technologies containing a more inert surface specifically designed to address difficult to analyze
analytes, MaxPeak High Performance Surfaces (HPS).5-10 The ACQUITY Premier UPLC BSM System has this
technology implemented across the entire fluidic path in order to provide a very effective barrier that significantly
reduces analyte interactions with all types of metal surfaces. Along with the ACQUITY Premier
OST Columns introduced in 2020, the entire UPLC System was recently tested for bioanalysis related LC-MS
applications of oligonucleotides.9 Here we investigated the capabilities of this UPLC system for intact mass
confirmation of oligonucleotides and their associated impurities. All datasets were acquired in full scan MS mode
on the BioAccord System with ACQUITY Premier and processed in waters_connect using the BayesSpray mass
spectral charge deconvolution algorithm to produce accurate intact mass measurements for each compound.
2
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Figure 1. Components of the BioAccord LC-MS System with ACQUITY Premier.
Experimental
Reagents and Sample Preparation
Triethylamine (TEA, 99.5% purity, catalogue number 65897-50ML) and methanol (LC-MS grade, catalogue
number 34966-1L) were obtained from Honeywell (Charlotte, NC), while 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP,
99% purity, catalogue number 105228-100G) was purchased from Sigma Aldrich (St Louis, MO). HPLC grade
deionized (DI) water was purified using a MilliQ system (Millipore, Bedford, MA). Mobile phases were prepared
fresh and used on the same day. A 21-mer heavily modified oligonucleotide, containing a 2’-OMe modification on
19 of its nucleosides, having the sequence GUA ACC AAG AGU AUU CCA UTT and the elemental composition C
229H306N76O143P20 was purchased from ATDBio (Southhampton, UK). Stock solutions were prepared in DI water
at a concentration of 1 µM (or 2.34 µg/mL), from which a 10 µL volume was injected, which corresponds to
loading 10 picomoles of the 21-mer oligonucleotide on-column.
3
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
LC Conditions
LC-MS system:
BioAccord System with ACQUITY Premier
Columns:
1) ACQUITY Premier OST Column 1.7 µm, 130 Å, 2.1
x 100 mm, (p/n: 186009485)
2) Conventional ACQUITY OST Column 1.7 µm, 130
Å, 2.1 x 100 mm, (p/n: 186003950)
3) ACQUITY Premier OST Column 1.7 µm, 130 Å,
2.1 x 50 mm, (p/n: 186009484)
Column temperature:
60 °C
Flow rate:
300 µL/min
Mobile phases:
Solvent A: 40 mM HFIP (hexafluoroisopropanol), 7
mM TEA (triethylamine) in DI water
Solvent B: 20 mM HFIP (hexafluoroisopropanol),
3.5 mM TEA (triethylamine) in 50% methanol
Sample temperature:
6 °C
Sample vial:
Certified Clear Glass Vials (p/n: 186000327C)
Injection volume:
10 µL
Wash solvents:
Purge solvent: 50% MeOH
Sample Manager wash solvent: 50% MeOH
Seal wash: 20% acetonitrile in DI water
4
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Gradient
MS Conditions
Ionization mode:
ESI(-)
Capillary voltage:
0.8 kV
Cone voltage:
40 V
Source temperature:
120 °C
Desolvation temperature:
400 °C
Desolvation gas (N2) pressure:
6.5 bar
Tof mass range:
400–5000
Acquisition rate:
2 Hz
Lock-mass:
waters_connect Lockmass solution (p/n:
186009298)
Data acquisition software:
waters_connect
Data processing software:
waters_connect
5
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Results and Discussion
A 21-mer oligonucleotide containing a variety of low-level oligonucleotide impurities was separated on two C18
columns, a regular 2.1 x 100 mm OST column (p/n: 186003950 <
https://www.waters.com/nextgen/us/en/shop/columns/186003950-acquity-uplc-oligonucleotide-beh-c18-
column-130a-17--m-21-mm-x-1.html> ) and a recently introduced ACQUITY Premier 2.1 x 100 mm OST Column
(p/n: 186009485 <https://www.waters.com/nextgen/us/en/shop/columns/186009485-acquity-premier-
oligonucleotide-c18-column-130a-17--m-21-x-100-m.html> ). For the 21-nt oligomer, a significant portion of the
molecule (19 nucleosides) contained modified nucleobases (as illustrated in the sequence listed in the
experimental section and in Figure 2). The 2’-OMe modification was attached to three guanosines (G) labeled in
blue and seven adenosines (A) labeled in green in the oligonucleotide sequence. Besides the attachment of the
same 2’-OMe functional group to uridines and cytidines, the nucleobases of these two nucleosides were further
modified by the attachment of a 5-Methyl group to produce five 2’-OMe 5-Me uridines (U, labeled in purple) and
four 2’-OMe 5-Me cytidines (C, labeled in red). The only nucleosides left unmodified are the two deoxythymidines
(TT) at the 3’-end of the 21-mer. All the oligonucleotide modifications can be summarized in the following
sequence: OMEG OME5mU OMEA OMEA OME5mC OME5mC OMEA OMEA OMEG OMEA OMEG OME5mU
OMEA OME5mU OME5mU OME5mC OME5mC OMEA OME5mU dT dT, which uses a specially designed
nomenclature. When analyzed on the ACQUITY Premier OST Column, the separation of the 21-nt oligonucleotide
reveals a rather complex impurity profile as shown in Figure 2A. Fourteen oligonucleotide impurities were
separated and detected by both TUV and MS detectors. Analysis of the same sample on a conventional column
(with stainless-steel casing), having the same dimensions and packed with the same stationary phase (C18 1.7 µm
particles, 130 Å pores), resolved only half (seven) of the same impurities, completely missing a significant portion
of the early eluting impurities, as indicated in Figure 2B. A recent publication7 indicated that untreated column
frits are mainly responsible for analyte adsorption on metal surfaces. The results presented in Figure 2B can be
explained by considering the adsorption effects of oligonucleotides on the inlet and outlet frit of a conventional
column. When the sample is loaded at the inlet of the column, the major oligonucleotide component can be used
to passivate the inlet frit, such that minor oligonucleotide impurities are not adsorbed to this frit. However, after
undergoing the IP-RP separations, because most of the oligonucleotide impurities elute before the major
component, there is a great possibility that the outlet frit would retain some of these impurities until it gets fully
passivated. It is very likely that in the example shown in Figure 2B, the first seven early eluting impurities were
not detected because they were adsorbed to the outlet frit.
6
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Figure 2. TUV chromatograms
showing the separation of oligonucleotide impurities from a 21-nt sample: (A) UV chromatogram recorded on an
ACQUITY Premier OST Column; (B) UV chromatogram recorded on an extensively conditioned conventional
column. The red traces from each figure correspond to the blanks preceding each injection; (3) Three replicates
injections performed on the ACQUITY Premier OST Column. For better clarity, the red and blue traces are offset
by +0.2 min from the previous trace.
The ACQUITY Premier OST Column belongs to a family of columns packed with sub 2 µm particles, featuring the
MaxPeak High Performance Surfaces (HPS) Technology.8-10 Oligonucleotides contain a negatively charged
phosphate backbone known to interact with metal surfaces (like stainless-steel, titanium, or MP35N—a Ni-Co
7
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
alloy) typically found in the fluidic path of the UPLC system. These interactions are often responsible for
oligonucleotide losses, poor chromatographic peak shapes, or poor data reproducibility. The MaxPeak HPS
Technology implemented along the UPLC fluidic path and the OST Column significantly reduced these
unwanted interactions, as demonstrated by the number and % abundance (related to UV peak areas) of
impurities detected. The conventional OST Column showed much more modest results in terms of impurity
recovery, even after extensive passivation. The separations performed on the ACQUITY Premier Column are
highly reproducible, as shown in Figure 2C where three replicate injections are overlaid. The ESI-MS spectrum of
the major oligonucleotide component is presented in Figure 3A. The lowest abundance impurity (0.18%
according to the UV data, see Table 1), confidently identified based on its ESI-MS spectrum, is an 11-mer
oligonucleotide missing all 10 nucleosides from the 5’-end of the molecule. The ESI-MS spectrum of this impurity
showing two major charge states (doubly and triply charged ions) is displayed in Figure 3B in the bottom panel.
There was no signal detected for this impurity in UV (see Figure 2B) and the ESI-MS spectrum recorded at the
expected elution time (top panel of Figure 3B) indicates that, very likely, this impurity was trapped (irreversibly
adsorbed) by metal surfaces inside the regular column (outlet column frit very likely), as the
same ACQUITY Premier UPLC System was used in both experiments. The full list of oligonucleotide impurities
detected in the 21-mer analyzed here is displayed in Table 1, along with their sequences, elemental compositions,
accurate average masses, and percent abundances calculated using the UV peak areas. The data presented in
Table 1 was used for setting up an automated processing using the BayesSpray charge deconvolution algorithm
from waters_connect and Figure 4 illustrates the processing results obtained. All fourteen oligonucleotide
impurities were detected across a relatively wide dynamic range (~500 fold) with deconvoluted mass accuracies
under 15 ppm.
8
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Figure 3. Ion pairing reversed-phase (IP-RP) ESI-MS spectra recorded for: (A) the most abundant sample
component, the 21-mer heavily modified oligonucleotide; (B) the least abundant sample component, an 11-mer
oligonucleotide impurity (see Table 1 for its sequence), present at 0.18% according to the UV peak area
measurement. All the oligonucleotide modifications are summarized using a specially designed nomenclature as
shown in Figure 3A.
9
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Table 1. Fourteen oligonucleotide impurities identified in a 21-mer extensively modified oligonucleotide.
Figure 4. Screenshot showing the waters_connect processing results obtained after BayesSpray charge
deconvolution of the ESI-MS spectra recorded for the 21-mer major component and fourteen of its
oligonucleotide impurities. The mass accuracy error for measuring the accurate average masses was better than
15 ppm for all sample components. The row corresponding to the main component is highlighted in blue and
indicates a purity of 83.03%, while the abundance of the lowest abundant species (an 11-mer oligo) was 0.18%
(highlighted by a red circle).
While it is important to be able to detect low-level oligonucleotide impurities with both UV and MS detectors, it is
equally important to measure their abundances accurately. In other words, it is critical that these impurities
produce a linear response in UV over the same dynamic range (~500 fold). To test the linearity of the UV assay,
the 21-mer oligonucleotide was diluted and analyzed on a shorter ACQUITY Premier Column (2.1 x 50 mm, p/n:
186009484 <https://www.waters.com/nextgen/us/en/shop/columns/186009484-acquity-premier-
oligonucleotide-c18-column-130a-17--m-21-x-50-mm.html> ) using faster (15-min) LC-MS runs. The UV
chromatogram recorded for lowest detected concentration of 0.5 nM, corresponding to a 1:2000 dilution of the
stock sample (1 µM), is shown in Figure 5A along with the preceding blank injection. Four replicate injections of
10
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
the same solution (0.5 nM or 1.17 ng/mL) have peak area RSDs under 15%, demonstrating that low-level
oligonucleotides can be analyzed reproducibly on the ACQUITY Premier Columns as highlighted in Figure 5B. A
calibration plot, showing the UV response (peak area) for a wide range of concentrations of the 21-nt oligomer
(eight concentrations in the range of 0.5 nM to 1000 nM), is presented in Figure 6. Taken together, the data
presented in Figures 5A, B, and Figure 6 clearly proves that the 21-mer oligonucleotide displays a linear
chromatographic behavior over a wide dynamic range (2000 fold) and has very good column recoveries even at
the lowest concentration - 0.5 nM, which corresponds to 5 femtomoles (or ~12 picograms) of oligonucleotide
loaded on-column. Finally, the carryover of the assay was evaluated by the injection of a Solvent A blank (10 µL)
right after the last replicate of the highest oligonucleotide concentration analyzed (1 µM). The result is displayed
in Figure 5C and it emphasizes the inertness of the ACQUITY Premier UPLC System and Column: there is no
detectable signal for the 21-mer oligonucleotide following the injection of a large amount (10 picomoles) on-
column.
11
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Figure 5. Testing the inertness
of the ACQUITY Premier UPLC System and ACQUITY Premier OST Column using the 21-nt oligomer: (A) UV
chromatogram of the lowest detectable concentration (0.5 nM, or 5 femtomoles of the 21-mer oligonucleotide
loaded on-column) compared against the preceding blank injection; (B) replicate UV chromatograms obtained
for the lowest detectable concentration (0.5 nM), indicating that the UV peak areas had RSDs below 15%; (C)
carryover evaluation, showing the UV chromatogram of a blank injection (red trace) following the injection of the
highest sample concentration (1000 nM or 10 picomole oligonucleotide loaded on-column). There is no
detectable signal from the 21-mer in the blank, suggesting that the UPLC system and column do not retain any
analyte through non-specific adsorption to the various coated metal surfaces found in the fluidic flow-path.
12
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Figure 6. Calibration curve of the 21-mer oligonucleotide showing linearity over three orders of
magnitude. Peak areas obtained from the TUV detector were plotted against a wide range of
oligonucleotide concentrations, including 0.5, 1, 5, 10, 20, 100, 200, and 1000 nM. Excellent signal
linearity was obtained for this assay, indicating that very low oligonucleotide concentrations can be
recovered completely from a very inert LC system that does not interact in any way with the analyte.
The inset shows the calibration curve in the 0.5–10 nM concentration range.
In conclusion, the BioAccord System with ACQUITY Premier is capable of measuring and accurately detecting
oligonucleotide impurities down to 0.2% and also provides intact mass confirmation capabilities via an
automated, compliance-ready workflow using the waters_connect Software.
Conclusion
A category of products incorporating the MaxPeak High Performance Surfaces (HPS) – including the
ACQUITY Premier UPLC BSM System and the ACQUITY Premier OST Columns – provide critical advantages
for oligonucleotide impurity analysis
■
Improved oligonucleotide analysis in terms of low detection limit and chromatographic reproducibility is
demonstrated using the BioAccord LC-MS System with ACQUITY Premier operated under compliant-ready
■
13
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
software
The oligonucleotide impurity analysis workflow provides mass confirmation for oligonucleotide impurities as
well as their relative abundance. The results from our study indicate that the LC-MS platform provides good
mass accuracy (better than 15 ppm) for intact mass confirmation of modified oligonucleotides and their
impurities, while the LC-UV information allows for the measurements of all the sample components, down to
0.2% relative abundance levels
■
References
Sharma VK, Watts JK Oligonucleotide Therapeutics: Chemistry, Delivery and Clinical Progress, Future Med
Chem, 2015, 7(16), 2221–2242.
1.
Roberts TK, Langer R, Wood MJA Advances in Oligonucleotide Drug Delivery, Nat Reviews, 2020, 19, 673–694.
2.
Catalin E. Doneanu, Jonathan Fox, Emma Harry, Chris Knowles, Ying Qing Yu, Joseph Fredette, Weibin Chen.
An Automated Compliance-Ready LC-MS Workflow for Intact Mass Confirmation and Purity Analysis of
Oligonucleotides, 2020, Waters Application Note, 720006820EN.
3.
Catalin E. Doneanu, Jonathan Fox, Emma Harry, Chris Knowles, Ying Qing Yu, Joseph Fredette, Weibin Chen.
Intact Mass Confirmation Analysis on the BioAccord LC-MS System for a Variety of Extensively Modified
Oligonucleotides, 2020, Waters Application Note, 720007028EN.
4.
M. Lauber, T. H. Walter, M. Gilar, M. DeLano, C. Boissel, K. Smith, R. Birdsall, P. Rainville, J. Belanger, and K.
Wyndham. Low Adsorption HPLC Columns Based on MaxPeak High Performances Surfaces, 2020, Waters
White Paper, 720006930EN <https://www.waters.com/webassets/cms/library/docs/720006930en.pdf> .
5.
DeLano M, Walter TH, Lauber MA, Gilar M, Jung MC, Nguyen J, Boissel C, Patel AV, Bates-Harrison A,
Wyndham K Using Hybrid Organic-Inorganic Surface Technology to Mitigate Analyte Interactions with Metal
Surfaces in UHPLC, Anal Chem, 2021, 93, 5773–5781.
6.
Gilar M, DeLano M, Gritti F Mitigation of Analyte Loss on Metal Surfaces in liquid chromatography, J Chrom A,
2021, 1650, 5773–5781.
7.
Amit Patel, Jennifer Simeone, Mathew Delano, Jason Dyke, Susan C. Rzewuski, Moon Chul Jung, Stephen J.
Shiner. Waters Premier Standards to Investigate the Inertness of Chromatographic Surfaces, 2021, Waters
Application Note, 720007105EN.
8.
14
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier
Kathryn Brennan, Mary Trudeau, Paul D. Rainville. Utilization of the ACQUITY Premier System and Column for
Improved Oligonucleotide Bioanalytical Chromatographic Performance, 2021, Waters Application Note,
9.
Brooke M. Koshel, Robert E. Birdsall, Ying Qing Yu. Improving Recovery and Quantitation of Oligonucleotide
Impurities Using the ACQUITY Premier with MaxPeak HPS Technology, 2021, Waters Application Note,
10.
Featured Products
BioAccord LC-MS System with ACQUITY Premier <https://www.waters.com/waters/nav.htm?cid=135087537
■
ACQUITY Premier System <https://www.waters.com/waters/nav.htm?cid=135077739>
■
ACQUITY UPLC Tunable UV Detector <https://www.waters.com/514228>
■
ACQUITY RDa Detector <https://www.waters.com/waters/nav.htm?cid=135077027>
■
waters_connect <https://www.waters.com/waters/nav.htm?cid=135040165>
■
720007301, July 2021
© 2021 Waters Corporation. All Rights Reserved.
15
Analysis of Oligonucleotide Impurities on the BioAccord System with ACQUITY Premier