<h3><strong>How long does it actually take to install all the capillaries and fittings on a conventional HPLC system?</strong></h3><h4><strong>The Small Components That Matter Most</strong></h4><p>When people think about HPLC systems, they often focus on pumps, detectors, columns, or software. Capillaries and fittings are usually seen as minor components because they are relatively inexpensive and physically small. However, every chromatographer eventually discovers that these tiny parts can have a major influence on system performance.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Connecting_a_U_HPLC_system_can_be_difficult_at_some_poorly_accessible_locations_3b837b441b.webp" alt="KNAUER: Connecting a (U)HPLC system can be difficult at some poorly accessible locations" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Connecting_a_U_HPLC_system_can_be_difficult_at_some_poorly_accessible_locations_3b837b441b.webp 208w," sizes="100vw" width="720" height="540"></p><p>Even decades ago, chromatographers recognized the importance of proper connections. In the 1980s, long before UHPLC became common, John Dolan wrote about minimizing dead volume through correct fitting installation. Today, with UHPLC systems operating at extremely high pressures and using columns with very small particle sizes, dead volume is even less tolerable than before. The topic remains just as relevant today as it was back then.</p><p>Interestingly, despite what many users assume, the chromatographic column itself is often not the primary source of HPLC or UHPLC problems. In my experience, poor connections are far more commonly responsible for issues such as peak broadening, leaks, or loss of efficiency.</p><h4><strong>The Early Days of HPLC Capillaries</strong></h4><p>Anyone who has been working with HPLC for many years will probably remember the era of rigid <strong>1/16" stainless steel tubing</strong>. Whenever PEEK tubing was unsuitable, stainless steel capillaries were the standard choice.</p><p>Setting up a system back then was far from convenient. You first had to locate an appropriate length of tubing somewhere in a drawer full of capillaries. Usually, this meant finding a several-meter-long piece and cutting it yourself using a dedicated capillary cutter. After cutting, you needed to ensure the tubing end was smooth and undamaged, hoping that the previous person using the cutter had not accidentally crushed the inner diameter.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Standard_1_16_Capillary_and_needed_tools_and_the_drawer_we_all_know_pretty_well_943d7ed0b2.jpg" alt="KNAUER: Standard 1/16” Capillary and needed tools and the drawer we all know pretty well" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Standard_1_16_Capillary_and_needed_tools_and_the_drawer_we_all_know_pretty_well_943d7ed0b2.jpg 245w," sizes="100vw" width="1277" height="456"></p><p>Once cut, the tubing often required additional preparation. You might need to deburr the capillary using a grater, shape it carefully with bending tools, and then finally install it using separate fittings and ferrules. And of course, everyone remembers the frustration of dropping a ferrule onto the laboratory floor, where it effectively disappeared forever.</p><p>At the same time, laboratories often accumulated drawers filled with pre-assembled capillaries that had fixed fittings attached. Reusing these assemblies was risky. If the fitting geometry did not perfectly match the receiving port, users could unintentionally introduce dead volume into the system. The result was often degraded chromatographic performance, broad peaks, and frustrating troubleshooting sessions involving the entire laboratory team. In worse cases, excessive force could damage threads or receiving ports while attempting to stop leaks.</p><p>During that period, assembling and connecting a complete HPLC system could easily consume half a day of work.</p><h4><strong>The Improvement: Flexible and Pre-Cut Capillaries</strong></h4><p>Later, laboratories gradually adopted pre-cut tubing and flexible capillaries, which represented a significant improvement over manually preparing stainless steel tubing.</p><p>With these newer capillaries, users simply selected the correct length and installed the tubing directly. Flexible capillaries adapted naturally to the required shape, eliminating much of the manual bending and shaping work. Installation became faster, easier, and far less stressful.</p><p>Still, these systems had limitations. Although the capillary itself improved, the fitting technology remained largely unchanged. Many of these capillaries were still effectively single-use components. If a connection was installed incorrectly because the tubing was not fully inserted into the receiving port before tightening, the result was often another unusable capillary destined for the growing “capillary drawer.” Sustainability was certainly not a strong point of these systems.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_A_typical_capillary_drawer_It_was_tricky_to_open_and_close_it_sometimes_530dd2087c.webp" alt="KNAUER: A typical capillary drawer. It was tricky to open and close it sometimes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_A_typical_capillary_drawer_It_was_tricky_to_open_and_close_it_sometimes_530dd2087c.webp 208w," sizes="100vw" width="1024" height="768"></p><p>Even with these advancements, system setup still required considerable time and effort.</p><h4><strong>The Real Breakthrough: Modern Tool-Free Connection Systems</strong></h4><p>A major breakthrough finally arrived when manufacturers introduced a completely redesigned fitting and capillary concept aimed specifically at simplifying UHPLC connections.</p><p>These newer systems came with fittings pre-installed directly on the capillary. Unlike traditional ferrule-based systems, the fittings automatically adjusted to different port depths and sealed directly at the bottom of the port. This dramatically reduced the amount of torque required and eliminated the need for complicated installation techniques.</p><p>Perhaps the biggest advantage was convenience. These capillaries could be connected and disconnected more than 100 times without tools, while remaining entirely finger-tight. And best of all, ferrules no longer disappeared onto the laboratory floor.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_The_little_things_that_do_the_click_3a0469d516.jpg" alt="KNAUER: The little things that do the “click”" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_The_little_things_that_do_the_click_3a0469d516.jpg 245w," sizes="100vw" width="1866" height="1022"></p><p>The system I currently use includes an especially useful feature: a patented torque-limiting mechanism that prevents both under-tightening and over-tightening. Once the correct torque is reached, the fitting produces a tactile “<strong>click</strong>,” providing immediate feedback that the connection is secure and properly installed every time.</p><h4><strong>From Half a Day to Fifteen Minutes</strong></h4><p>Thanks to these modern connection systems and pre-configured startup kits, installing an HPLC or UHPLC system today is dramatically faster than it used to be.</p><p>What once consumed hours of work can now be completed in less than 15 minutes. The improvements in usability, reproducibility, and sustainability over recent years have been remarkable.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Trouble_free_connection_systom_for_HPLC_and_UHPLC_e62b80154b.webp" alt="KNAUER: Trouble-free connection systom for HPLC and UHPLC" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Trouble_free_connection_systom_for_HPLC_and_UHPLC_e62b80154b.webp 221w," sizes="100vw" width="690" height="487"></p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Trouble_free_connection_systom_for_HPLC_and_UHPLC_2_71c24acdf5.webp" alt="KNAUER: Trouble-free connection systom for HPLC and UHPLC" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Trouble_free_connection_systom_for_HPLC_and_UHPLC_2_71c24acdf5.webp 224w," sizes="100vw" width="1920" height="1339"></p><p>And while today’s solutions already represent a huge leap forward, the evolution of HPLC connection technology is certainly not over yet. Looking ahead, it will be exciting to see how future innovations continue to simplify chromatography workflows even further.</p><blockquote><p>If you want to learn more about KNAUER´s capillaries, fittings and (U)HPLC system start-up kits and are interested in details and numbers, I highly recommend our brand <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/r75ev6rjivdbid246k60zrs3gjpvwdi5b8em_fad0f92fd9.pdf"><strong>new tech note "Benefits of KNAUER´s trouble-free analytical capillaries in terms of HPLC and UHPLC system performance</strong></a><strong>"</strong> and a visit to our <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/2402"><strong>products online</strong></a>.</p></blockquote>

Let´s Connect a whole (U)HPLC system without tools and trouble

News from LabRulezLCMS Library - Week 21, 2026

<p><strong>If you’ve reviewed your laboratory’s operational budget recently, you have likely noticed a troubling trend: the cost of keeping your instruments running is climbing, and nitrogen gas is a major culprit.</strong></p><p>According to Organomation’s newly released <a target="_blank" rel="noopener noreferrer" href="https://explore.organomation.com/nitrogen-usage-survey-2025-download"><strong>Nitrogen Usage 2025 Survey Report</strong></a>, you are not alone in this frustration. In fact, <strong>35% </strong>of laboratories ranked high costs as their number one frustration with their current nitrogen supply — overshadowing safety, logistics, and maintenance concerns.</p><p>With<strong> 96%</strong> of labs expecting their nitrogen demand to increase or remain steady over the next three years, waiting for prices to drop isn’t a viable strategy. To protect your budget, you need to understand why prices are surging and, more importantly, how to insulate your lab from the volatility.</p><h3><strong>The "Perfect Storm" Driving Prices Up</strong></h3><p>As a chemist, you know that nitrogen is abundant in the atmosphere. However, the industrial process of separating, purifying, compressing, and transporting it is energy-intensive and tied heavily to global markets. Three key factors are driving the 2025 price surge:</p><h4><strong>1. Rising Energy Costs</strong></h4><p>While nitrogen itself is free, the energy required to produce high-purity nitrogen gas (via fractional distillation) is not. Industrial gas manufacturing is heavily reliant on energy prices. In 2025, U.S. natural gas prices for industrial sectors have seen significant volatility, with some forecasts showing double-digit percentage increases for power plants due to export demands and tightening domestic supply. When the cost of energy rises,<a target="_blank" rel="noopener noreferrer" href="https://www.reuters.com/markets/commodities/energy/high-rising-natural-gas-costs-may-spur-fresh-climb-us-coal-use-2025-12-03/"><strong> gas suppliers pass those costs directly to the consumer</strong></a>.</p><h4><strong>2. The Logistics Premium</strong></h4><p>If you rely on high-pressure cylinders or liquid dewars, you aren't just paying for gas; you are paying for diesel, driver wages, and truck maintenance. Logistics frustrations were a top complaint in our 2025 survey, particularly for labs using liquid dewars.</p><ul><li><strong>Delivery Fees &amp; Surcharges: </strong>Fuel surcharges are now a standard line item on many invoices, fluctuating weekly with the oil market.</li><li><strong>Cylinder Rental: </strong>The "rent" for holding steel cylinders often creeps up annually, regardless of how much gas you actually consume.</li></ul><h4><strong>3. Hidden Waste (The "Boil-Off" Tax)</strong></h4><p>For labs using liquid nitrogen dewars, the "price per liter" is deceptive. Liquid nitrogen constantly boils off to maintain its temperature. If your lab uses dewars for gaseous applications (like evaporation), you are paying for gas that vanishes into the room before it ever reaches your instrument. Our survey found that while dewars nominally cost <strong>$2.06/liter</strong>, the <i>effective </i>cost is often higher due to this inevitable waste.</p><h3><strong>The Data: Cylinders vs. Generators</strong></h3><p>The most striking finding from our 2025 Survey Report was the massive price disparity between supply methods. When we analyzed the average cost per liter across <strong>78 laboratories</strong>, the data was clear:</p><h5><strong>Nitrogen Source</strong>: <strong>Average Cost Per Liter</strong></h5><ul><li><strong>Gas Cylinders</strong>: $2.79</li><li><strong>Liquid Dewars</strong>: $2.06</li><li><strong>Lab-Scale Generator</strong>: $0.70</li></ul><p>Laboratories relying on cylinders are paying nearly<strong> 400% more</strong> per liter than those generating their own gas. Over the course of a year, this difference can amount to thousands of dollars in operational waste.</p><h3><strong>How to Reduce the Price Tag: A Two-Step Strategy</strong></h3><p>You cannot control the global energy market or supply chain logistics. However, you can control how you source and use your nitrogen.</p><h4><strong>Step 1: Cut the Cord (Switch to Generation)</strong></h4><p>The single most effective way to lower your nitrogen spend is to stop buying it in tanks. While the upfront cost of equipment can sometimes be a hurdle for capital budgets, new financial models are making this transition accessible for labs of all sizes.</p><h5><strong>Why Generation Wins on Cost</strong></h5><p>A nitrogen generator, like the Organomation NITRO-GEN, separates nitrogen from your lab's existing compressed air supply using a hollow-fiber membrane. Once installed, your "cost per liter" drops to essentially zero—you are only paying for the electricity to run the compressor.</p><ul><li><strong>Rapid ROI: </strong>Most labs see a return on investment in 12 to 18 months by<a target="_blank" rel="noopener noreferrer" href="https://www.organomation.com/how-much-could-i-save-switching-to-a-nitrogen-generator"><strong> generating nitrogen</strong></a>. After this break-even point, your nitrogen supply becomes a fixed asset rather than a monthly liability.</li><li><strong>Operational Freedom: </strong>Weighing under 20 lbs and wall-mountable, the NITRO-GEN <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products/1902"><strong>N2 generator</strong></a><strong> </strong>produces up to 20 L/min of gas, sufficient to support blowdown evaporators with up to 48 sample positions.</li></ul><h5><strong>Overcoming the "Sticker Shock" with Lease-to-Own</strong></h5><p>Historically, the barrier to entry for nitrogen generators has been the initial purchase price. To solve this, Organomation has introduced a Lease-to-Own program designed to align equipment costs with your operating budget rather than your capital reserves.</p><p>This program transforms a large capital expenditure into a manageable monthly operating expense. Unlike standard rental agreements where payments are lost forever, this program allows you to build equity.</p><ul><li><strong>Immediate Savings: </strong>You can install the unit and stop paying cylinder rental fees immediately, often letting the operational savings offset the lease payments.</li><li><strong>Path to Ownership: </strong>At the end of the lease term, you own the equipment outright—often for a nominal final payment (as low as $1).</li><li><strong>Preserve Capital:</strong> By spreading the cost over time, you keep your cash reserves available for other critical research needs or staffing.</li></ul><p>By leveraging a lease-to-own model, you can "cut the cord" on gas contracts today without waiting for next year’s capital budget approval.</p><h4><strong>Step 2: Optimize Your Usage (Stop Wasting Gas)</strong></h4><p>Even with a cheap supply, wasting gas is bad science and bad business. especially if you use nitrogen for sample concentration (blowdown evaporation).</p><ul><li><strong>Use Individual Flow Control:</strong> Many basic evaporators blow gas into every position, regardless of whether a sample is present. High-quality units (like the<a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/products?category=3&amp;manufacturerItems=540&amp;search=N-EVAP"><strong> N-EVAP</strong></a>) feature individual needle valves for each sample position. Rule of thumb: If you are running 10 samples in a 24-position unit, ensure the other 14 needles are closed.</li><li><strong>Check for Leaks:</strong> It sounds basic, but a loose fitting on a regulator can waste cylinders of gas over a weekend. A simple "snoop test" (soapy water) on your connections every quarter is a zero-cost maintenance habit that saves money.</li><li><strong>Optimize Bath Temperature: </strong>In nitrogen blowdown evaporation, gas flow and temperature work together. If your water bath is too cool, you have to blow gas for longer to <a target="_blank" rel="noopener noreferrer" href="https://blog.organomation.com/blog/optimum-temperature-for-nitrogen-evaporation-instruments"><strong>achieve dryness</strong></a>. Ensuring your bath is at the optimal temperature for your solvent (e.g., 35-40°C for DCM) reduces the total time the gas needs to run.</li></ul><h3><strong>Conclusion</strong></h3><p>The era of "cheap" delivered gas is likely behind us. As the 2025 survey data shows, labs sticking to the status quo of cylinders and dewars are facing rising costs and logistical headaches. By transitioning to on-demand generation and optimizing your evaporation workflows, you can insulate your lab from market volatility and keep your budget focused on research, not utility bills.</p><blockquote><p><strong>Want to see the full data?</strong><br>Download the<a target="_blank" rel="noopener noreferrer" href="https://explore.organomation.com/nitrogen-usage-survey-2025-download"><strong> Laboratory Nitrogen Usage Report </strong></a>to benchmark your lab’s spending against industry peers.</p><p><strong>Curious about your potential savings?</strong><br>Try our <a target="_blank" rel="noopener noreferrer" href="https://www.organomation.com/how-much-could-i-save-switching-to-a-nitrogen-generator"><strong>Nitrogen Generator Savings Calculator </strong></a>to see exactly how much you could save by making the switch.</p></blockquote>

Why Nitrogen Is Costing Labs More Than Ever — And How to Reduce the High Price Tag

Article

Product

Application

Laboratories

Poster

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Organomation, founded in 1959, designs and manufactures high-quality nitrogen evaporators and extraction systems. Known for innovation and durability, their lab instruments are used globally for efficient sample preparation with strong customer support.

Organomation

Based in Berlin, KNAUER is a medium-sized, owner-managed company that has been serving the sciences since 1962. We develop and manufacture scientific instruments of superior quality for liquid chromatography, including: Analytical HPLC/UHPLC, Preparative HPLC, Fast protein liquid chromatography (FPLC), Multi-column chromatography/Simulated moving bed (SMB) chromatography. High pressure dosing, in-line detection systems, and osmometry are additional business areas.

KNAUER

Waters Sample & Collection Plate

Waters 96-well and 384-well plates are adherent to ANSI and SBS standards and are suitable for LC autosamplers and liquid handling robots.

<div><div><h4><strong>Broad selection of high-quality sample and collection plates</strong></h4></div></div><div><div><p><strong>Waters 96-well and 384-well plates are adherent to ANSI and SBS standards and are suitable for LC autosamplers and liquid handling robots. Waters plates are made from polypropylene (PP) for chemical resistance, and specialty 96-well plates with glass inserts are available for samples that are not suitable for polypropylene containers.</strong></p><h3><strong>Overview</strong></h3><div><div><div><div><div><div><ul><li>96- and 384-well collection plates and sample plates are SBS/ANSI compliant for robotic compatible systems&nbsp; &nbsp; &nbsp; &nbsp;</li><li>&nbsp;Constructed of polypropylene (PP) for chemical resistance</li><li>&nbsp;Glass inserts available for samples requiring glass surfaces</li><li>&nbsp;Heat seals and cap mats for plates and glass inserts</li></ul></div></div><div><div><h4><strong>Recommended Use</strong></h4><p>For general high-throughput LC and LC-MS work and for integration in (semi)-automated sample handling workflows.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/img_Waters_Sample_and_Collection_Plate_709693fdab.jpg" alt="imgWaters Sample &amp; Collection Plate." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_img_Waters_Sample_and_Collection_Plate_709693fdab.jpg 245w," sizes="100vw" width="1024" height="493"></p><h3><strong>Cap Mats</strong></h3><h4><strong>Silicone/PTFE &amp; Polypropylene Cap Mats</strong></h4><ul><li>Non-slit storage mats for long-term sample storage</li><li>Pre-slit silicone/PTFE and polypropylene cap mats for use in autosamplers for proper venting and sample draw accuracy with excellent resealing characteristics</li><li>Silicone/PTFE &amp; Polypropylene Cap Mats</li></ul><h3><strong>Heat Seals</strong></h3><h4><strong>Clear Polyester Heat Seals</strong></h4><ul><li>Can be used with most solvents &amp; buffers over a -80 °C to 80 °C temperature range</li><li>Requires a heat sealer to apply</li></ul><h4><strong>Aluminum Foil Heat Seals</strong></h4><ul><li>Made from a polyester/aluminum laminate</li><li>Ideal choice for long term storage to reduce evaporative loss</li><li>Aluminum layer reduces gas permeability of the seal</li><li>Can be used at temperatures from -200 °C to 90 °C</li><li>Requires a heat sealer to apply</li></ul><h4><strong>Adhesive Seals</strong></h4><ul><li>A polyolefin film with synthetic rubber adhesive</li><li>Ideal for use with protein and peptide samples and buffers</li><li>Resistant to small concentrations (0% to 30%) of polar organic solvents</li><li>Can be used at temperatures from -80 °C to 80 °C</li><li>Requires a heat sealer to apply</li></ul></div></div></div></div></div></div></div></div>

Waters CERTIFIED HPLC Vials

Reducing failed assays from unknown contaminant peaks and limiting instrument downtime from out of specification vials is a priority for your lab. Waters sample vials can help you do just that.

<div><div><h4><strong>Meet your analytical challenges with the right vial.</strong></h4></div></div><div><div><p><strong>The right vial.&nbsp;</strong><span><strong>A world of difference.</strong></span></p><p>Reducing failed assays from unknown contaminant peaks and limiting instrument downtime from out of specification vials is a priority for your lab. Waters sample vials can help you do just that.</p><p>All Waters sample vials are held to the tightest dimensional tolerances. Manufactured via a 2-, 3-, or 4-step certification process, we ensure that Waters Certified Vials meet and maintain specified vial dimensions, levels of cleanliness and adsorption properties from batch to batch.&nbsp;Find the right vial for your application and autosampler - use our <a target="_blank" rel="noopener noreferrer" href="https://find.waters.com/VialSelector/"><strong>Vial Selector</strong></a> to find your perfect match.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_118649175c.jpg" alt="Waters CERTIFIED Vials: Table 1. Vials for Routine and Advanced Analyses." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_118649175c.jpg 245w," sizes="100vw" width="1226" height="754"></p><h3><strong>Waters LCMS CERTIFIED</strong></h3><p><span><strong>✅ </strong></span>Dimensional Test</p><p><span><strong>✅ </strong></span>Septum GC Test</p><p><span><strong>✅ </strong></span>HPLC UV Test</p><p><span><strong>✅ </strong></span>MS Scan</p><ul><li>Low MS interferences from known residues &amp; polymers</li><li>For routine QC and LC-MS analysis with lower analyte concentrations from 10-100s ng/ml.</li></ul><h3><strong>Waters TruView<sup>TM</sup> LCMS CERTIFIED</strong></h3><p><span><strong>✅ </strong></span>Dimensional Test</p><p><span><strong>✅ </strong></span>Septum GC Test</p><p><span><strong>✅ </strong></span>HPLC UV Test</p><p><span><strong>✅ </strong></span>MS Scan</p><p><span><strong>✅&nbsp;</strong></span>Low Adsorption Test</p><div><div><ul><li>Lowest MS interferences from known residues &amp; polymers</li><li>For high-end LC-MS analysis and quantification of analytes with a concentration of below 1 ng/ml with reduced adsorption of polar analytes.</li></ul><h3><strong>Waters CERTIFIED</strong></h3><p><span><strong>✅ </strong></span>Dimensional Test</p><p><span><strong>✅ </strong></span>Septum GC Test</p><p><span><strong>✅ </strong></span>HPLC UV Test</p><div><div><ul><li>No UV interferences caused caused by manufacturing and packaging residues</li><li>For routine QC LC-UV analysis&nbsp;of compounds in µg/mL&nbsp;concentrations.&nbsp;</li></ul><h3><strong>MAXPEAK QuanRecovery</strong></h3><ul><li>For high recovery peptide and protein quantification workflows. Reduces sample losses due to non-specific binding (NSB) and ionic interactions.</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_2_4fba532335.jpg" alt="Waters CERTIFIED Vials: Vials Shapes." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_2_4fba532335.jpg 245w," sizes="100vw" width="1261" height="617"></p><div><div><h3><strong>Control data quality risks and reduce unexpected or ghost peaks</strong></h3><p>Don’t let the presence of background noise impact your results, causing data quality risks and unexpected or ghost peaks. Background noise can come from many factors.&nbsp;One of the most important factors are vial and septa cleanliness, which introduces contamination peaks. Ghost peaks are introduced by analyte degradation that can be triggered by significant pH changes in the diluent. In this chromatogram, the top shows normal behavior, and the bottom chromatogram shows ghost peaks.</p><p>Waters Certified vials are cleanliness tested so you don’t have to worry about contaminant peaks. The TruView pH Control Vials are certified to minimize and control a pH shift away from the neutral.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_4_7749301ba1.jpg" alt="Waters CERTIFIED Vials: Prevent the appearance of unexpected peaks during LC/UV analysis with Waters LC/GC Certified Vials as a control strategy." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_4_7749301ba1.jpg 245w," sizes="100vw" width="1024" height="535"></p><h3><strong>More time on development. Less on troubleshooting</strong></h3><p>Stop losing valuable development time on troubleshooting due to analyte loss from non-specific adsorption. Waters TruView pH Control LCMS Certified Vials have the lowest adsorptive losses on the market, and you can rely on them to provide consistency from batch to batch and vial to vial. This chromatogram shows a comparison of adsorptive loss of chlorhexidine in a variety of vials.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_5_d3e42fa7f2.jpg" alt="Waters CERTIFIED Vials: Comparison of adsorptive loss of chlorhexidine acetate in a variety of vials." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_5_d3e42fa7f2.jpg 245w," sizes="100vw" width="1024" height="633"></p><div><div><h3><strong>Ideal for demanding MS work</strong></h3><p>LCMS Certified Vials are suited for analyte concentrations in the 100s ng/mL concentration. Waters LCMS Certified Vials are tested by MS scans from 250 to 1000 <i>m/z</i> with specifications set on the total ion count and presence of clusters in the high mass range. This chromatogram shows a comparison of typical MS scans of Waters LCMS Certified Vials to vials of other sources and clean solvents.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_3_4869fbf57a.jpg" alt="Waters CERTIFIED Vials: Comparing typical MS scans of Waters LCMS Certified Vials, with vials from other sources." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_3_4869fbf57a.jpg 245w," sizes="100vw" width="1024" height="406"></p><div><div><h3><strong>Stay in control of your samples' pH</strong></h3><p>The analysis of low abundance species, pH sensitive analytes or not yet well understood compound mixtures benefit from consistent and well controlled vial surfaces. The glass surface of TruView pH Control LCMS Certified Vials minimizes pH shifts away from the neutral and thus eliminates unwanted reactions and resulting ghost peaks.&nbsp;Ghost peaks are very difficult to troubleshoot.</p><p>Waters TruView pH Control LCMS Certified vials were used to analyze two compounds, drospirenone and lovastatin. The TruView pH Control LCMS Certified Vials show little to no degradant formed over the time tested. Standard glass vials showed considerable degradant formation over the same testing time with irreproducible formation of the degradant across different vials.&nbsp;</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_6_4dc330d849.jpg" alt="Waters CERTIFIED Vials: UV peak areas of lovastatin degradant across replicate vials and different vial types. Error bars indicate standard deviation for the replicate injection peak area." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_6_4dc330d849.jpg 245w," sizes="100vw" width="1024" height="605"></p><div><div><h3><strong>Reducing adsorption starts here</strong></h3><p>Inconsistent analytical results from small molecule analyte adsorption onto the surface of glass vials can be a problem at today’s low analyte concentrations. Some scientists have even experienced total analyte loss with samples stored in vials for an extended time. The vial chemistry, specifically the&nbsp;glass surface, is the major contributor to this problem.</p><p>Polar analytes&nbsp;may adsorb to the glass vial surface by polar-polar interaction and/or ion exchange mechanisms, thereby reducing the overall amount of sample in solution. TruView Certified LCMS Vials&nbsp;reduce this problem dramatically due to a stringent manufacturing process. The process yields a glass surface that has a lower concentration of free ions on the surface.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_CERTIFIED_Vials_8_064003b933.jpg" alt="Waters CERTIFIED Vials: Nortriptyline at 1 ppb concentration in several vials. The tall peak is the initial injection; the smaller peak (overlaid) is the four-hour injection. The first two chromatograms are competitor’s vials. The third chromatogram is for the Waters TruView LCMS Certified vial. " srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_CERTIFIED_Vials_8_064003b933.jpg 245w," sizes="100vw" width="1912" height="1182"></p><div><div><h3><strong>No analyte left behind</strong></h3><p>Instrument development is yielding more sensitive mass spectrometers. With more sensitive instruments, analytes can be detected at pg/mL levels. At these concentrations, understanding adsorption issues is critical for good quantitative results. We tested adsorption loss for the major manufacturers and saw high sample loss across manufacturers and clear and amber glass types – with significantly less loss with Waters TruView Autosampler Vials.</p><h4><strong>Average Analyte Loss</strong></h4><p><strong>Manufacturer: Clear Glass / Amber Glass</strong></p><ul><li><strong>Vendor A</strong>: 55% / 69%</li><li><strong>Vendor B</strong>: 25% / 25%</li><li><strong>Vendor C</strong>: 54% / 74%</li><li><strong>Vendor D</strong>: 18% / 59%</li><li><strong>Vendor E</strong>: 75% / Not tested</li><li><strong>Waters TruView LCMS Certified Vial</strong>: 1% / 6%</li></ul></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div></div>

Waters QuanRecovery HPS Vials & Plates

 QuanRecovery Vials and Plates minimize sample losses from NSB and ionic interactions, ensuring greater confidence in results and improved assay repeatability.

<div><div id="title-b8cf3c562d" data-locator="title-with-text"><h3><strong>Reduce sample losses due to non-specific binding (NSB)</strong></h3></div></div><div><div id="text-c1d5077d21" data-locator="text"><p><strong>Successfully quantitating proteins and peptides with LC–MS is often more challenging than doing so for small molecules. Their large and complex structure requires a different approach to LC–MS method development and may also cause other unique problems like nonspecific adsorption (or nonspecific binding). Proteins and peptides in solution tend to stick to the surfaces they encounter.</strong></p><p>Autosampler-ready QuanRecovery Vials and Plates with MaxPeak High Performance Surfaces (HPS)&nbsp;are designed to enable scientists like you to meet recovery, sensitivity and reproducibility challenges in LC-MS peptide and protein quantification. By reducing sample losses from non-specific binding (NSB) and ionic interactions, QuanRecovery Vials and Plates provide your lab greater confidence in analytical results and fewer long-term assay repeatability problems.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Quan_Recovery_HPS_Vials_and_Plates_Quan_Recovery_Vials_and_Plates_with_Max_Peak_HPS_ed65a9e3fe.jpg" alt="Waters QuanRecovery HPS Vials &amp; Plates: QuanRecovery Vials &amp; Plates with MaxPeak HPS." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Quan_Recovery_HPS_Vials_and_Plates_Quan_Recovery_Vials_and_Plates_with_Max_Peak_HPS_ed65a9e3fe.jpg 234w," sizes="100vw" width="1024" height="682"></p><div data-locator="section-container-body"><div><div><div data-locator="layoutcontainer-"><div><div id="text-b5ef0a0cdd" data-locator="text"><div><div id="text-62116091dc" data-locator="text"><h3 data-locator="modal-title"><strong>Improved LC-MS analysis of peptides and proteins</strong></h3><p>It can be difficult to predict peptide losses due to non-specific binding and ionic interactions, as losses can be dependent on many characteristics, including pI and hydrophobicity. Demonstrated here are the recovery of four different peptides.&nbsp;The recovery of desmopressin is not affected by the sample container, while glucagon, insulin, and melittin suffer varying losses due to non-specific binding and ionic interactions in the glass and standard polypropylene containers.&nbsp;</p><p>Only QuanRecovery Vials and Plates with MaxPeak HPS protect these peptides from loss, enabling you to achieve higher recovery and improved repeatability.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Quan_Recovery_vialky_a_platicka_pro_lepsi_analyzy_proteinu_a_peptidu_caa551b7f1/Waters-QuanRecovery-vialky-a-platicka-pro-lepsi-analyzy-proteinu-a-peptidu_l.webp" alt="Waters QuanRecovery HPS Vials &amp; Plates: A comparison of the recovery of four peptides prepared in a typical LC-MS diluent and stored in various sample containers." width="1074" height="466"></p></div></div></div></div></div></div></div></div></div></div><div><div id="text-455dc5902f" data-locator="text"><h3 data-locator="modal-title"><strong>Enhanced recovery and sensitivity at high and low sample concentrations</strong></h3><p>Biomolecule sample losses are a problem at low concentrations. However, non-specific binding and ionic interactions can also cause losses at higher concentrations. Such losses not only negatively impact the assay sensitivity, they also compromise the reproducibility, precision, and accuracy of the analysis. QuanRecovery Vials and Plates with MaxPeak HPS protect your sample, ensuring improved analytical results.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Quan_Recovery_HPS_Vials_and_Plates_Improved_recovery_and_sensitivity_at_high_and_low_sample_concentrations_with_Quan_Recovery_Plates_2816689528.jpg" alt="Waters QuanRecovery HPS Vials &amp; Plates: Improved recovery and sensitivity at high and low sample concentrations with QuanRecovery Plates." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Quan_Recovery_HPS_Vials_and_Plates_Improved_recovery_and_sensitivity_at_high_and_low_sample_concentrations_with_Quan_Recovery_Plates_2816689528.jpg 221w," sizes="100vw" width="1024" height="724"></p><h3><strong>Overview</strong></h3><div data-locator="section-container-body"><div><div><div data-locator="layoutcontainer-"><div><div id="text-9f8f97fb02" data-locator="text"><ul><li>For large molecule LC-MS bioanalysts who need the ultimate sensitivity, reproducibility and sample stability over multiple analyses.</li><li>Improve detection limits and analysis reproducibility for peptide and protein quantification with these low adsorption plates and vials.</li><li>Designed for LC-MS analysis in autosampler ready formats with low residual volumes in 700 µL 96-well plate and 300 µL sample vial formats.</li><li>Increase analyte recovery, sensitivity and reproducibility by minimizing analyte/surface interactions that can lead to sample losses with MaxPeak High Performance Surfaces (HPS).</li><li>Suitable for workflows with ACQUITY Premier Systems and Columns.</li></ul></div></div><div><div id="text-b5ef0a0cdd" data-locator="text"><h3><strong>Recommended Use</strong></h3><p>To minimize sample losses due to non-specific binding (NSB) and ionic interactions.</p></div></div></div></div></div></div></div></div>

Waters Oasis SPE products

Waters Oasis SPE products come in a broad range of sorbents and an array of formats. With Oasis products, you can meet a wide variety of sample preparation needs.

<h4><strong>Faster, cleaner, and simpler SPE starts here</strong></h4><p>Analytical chemists worldwide use SPE to remove interfering matrix compounds and enrich the analyte of interest to ensure the generation of high-quality data.</p><p>Waters Oasis SPE products come in a broad range of sorbents and an array of formats. With Oasis products, you can meet a wide variety of sample preparation needs, from simple and fast sample matrix clean-up to more complex sample preparation challenges.</p><p>Oasis SPE products deliver unmatched purity, consistency, and quality for sample analysis. Along with seven different SPE chemistries, Oasis SPE products use universal to customized protocols to handle your unique sample.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_SPE_kolonky_2_967d461f2e/Waters-Oasis-SPE-kolonky-2.jpg" alt="Waters: Oasis SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_SPE_kolonky_2_967d461f2e/thumbnail_Waters-Oasis-SPE-kolonky-2.jpg 245w," sizes="100vw" width="950" height="416"></p><h4><strong>Overview</strong></h4><ul><li>Fully water-wettable sorbents increase reproducibility and enable elimination of condition and equilibration steps</li><li>Co-polymer pH stable from 0–14 with no secondary silanol activity</li><li>Optimal sensitivity for small molecule and therapeutic peptide analysis</li><li>Reduced matrix effects for LC-MS/MS analyses</li><li>Unsurpassed selectivity</li><li>Consistent retention and capacity, yielding the highest SPE recovery</li><li>Reduces variability in analytical results and increases robustness of analysis</li><li><strong>Recommended Use: </strong>For the fastest, cleanest, and simplest approach to SPE-LC-MS/MS method development.</li></ul><h4><strong>Solid-Phase Extraction Chemistries</strong></h4><h5><strong>Oasis PRiME HLB</strong></h5><ul><li>Multi-purpose hydrophilic-lipophilic balanced reversed phase sorbent for acids, bases, and neutrals</li><li>Cleaner samples in fewer steps with simple three-and two-step protocols, no SPE expertise required</li><li>Removes 95% of common matrix interferences, such as proteins, salts, phospholipids, and pigments</li><li>No sorbent conditioning or equilibration steps required</li><li>Faster, more predictable analysis time</li><li>Ideal for reversed-phase SPE clean-up of samples in routine analysis.</li></ul><h5><strong>Oasis PRiME MCX</strong></h5><ul><li>Mixed-mode Cation eXchange sorbent to selectively retain, concentrate and elute basic compounds</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Cleaner samples in fewer steps with simple and fast 3 and 4-step protocols</li><li>Removes 99% of phospholipids from complex sample matrices</li><li>No sorbent conditioning or equilibration steps required</li><li>Faster, more predictable analysis time</li><li>Highly reproducible target analyte recoveries</li><li>Ideal for basic compound specificity while removing matrix interferences in a simple clean-up.</li></ul><h5><strong>Oasis HLB</strong></h5><ul><li>Multi-purpose hydrophilic-lipophilic balanced reversed phase sorbent</li><li>Provides high capacity for acids, bases, and neutrals</li><li>Ideal for ultra-high capacity of very polar compounds.</li></ul><h5><strong>Oasis MCX</strong></h5><ul><li>Mixed-mode Cation eXchange sorbent for bases</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for selective retention of basic analytes.</li></ul><h5><strong>Oasis MAX</strong></h5><ul><li>Mixed-mode Anion eXchange for acids</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for selective retention of acidic analytes.</li></ul><h5><strong>Oasis WAX</strong></h5><ul><li>Weak Anion eXchange mixed-mode sorbent for strong acidic compounds</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for improved retention of strong acidic compounds.</li></ul><h5><strong>Oasis WCX</strong></h5><ul><li>Weak Cation eXchange mixed-mode sorbent for strong basic compounds</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for improved retention of all basic analytes, especially strong bases.</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Sorbenty_Oasis_SPE_na_bazi_kopolymeru_Oasis_HLB_c8ffee39b3/Waters-Sorbenty-Oasis-SPE-na-bazi-kopolymeru-Oasis-HLB.png" alt="Waters: Oasis Sorbents" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Sorbenty_Oasis_SPE_na_bazi_kopolymeru_Oasis_HLB_c8ffee39b3/thumbnail_Waters-Sorbenty-Oasis-SPE-na-bazi-kopolymeru-Oasis-HLB.png 211w," sizes="100vw" width="1511" height="1119"></p><h4><strong>Oasis Formats</strong></h4><h5><strong>Oasis μElution Plate</strong></h5><ul><li>Patented μElution plate design</li><li>No evaporation and reconstitution necessary due to elution volumes as low as 25 µL</li><li>Ideal for SPE clean-up and analyte enrichment of small sample volumes</li><li>Compatible with most liquid-handling robotic systems for automated, reliable high-throughput SPE (HT-SPE)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_m_Elution_Plate_aa7e36a4c1.jpg" alt="Waters: Oasis µElution Plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_m_Elution_Plate_aa7e36a4c1.jpg 245w," sizes="100vw" width="502" height="260"></p><h5><strong>Oasis 96-Well Sample Extraction Plates</strong></h5><ul><li>Innovative, award-winning two-stage well design</li><li>High throughput and high recovery</li><li>Compatible with most liquid-handling robotic systems for automated, reliable high-throughput SPE (HT-SPE)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_96_Well_Sample_Extraction_Plates_9528d532b9.jpg" alt="Waters: Oasis 96-Well Sample Extraction Plates" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_96_Well_Sample_Extraction_Plates_9528d532b9.jpg 245w," sizes="100vw" width="525" height="329"></p><h5><strong>Oasis Syringe-Barrel Cartridges</strong></h5><ul><li>Ultra-clean syringe barrel and frits</li><li>Available in cartridges ranging from 1 cc to 60 cc</li><li>Flangeless syringe-barrel cartridges available in 1 cc, 3 cc, and 6 cc sizes</li><li>Plus-style cartridges with Luer inlet hub and outlet tip, compatible with hand-held syringes</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_Syringe_Barrel_Cartridges_961aa06b8a.jpg" alt="Waters Corporation: Oasis Syringe-Barrel Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_Syringe_Barrel_Cartridges_961aa06b8a.jpg 245w," sizes="100vw" width="503" height="311"></p><h5><strong>Oasis Glass Cartridges</strong></h5><ul><li>Ultra-clean glass syringe with Teflon® frit</li><li>For trace level detection and analysis at part-per-trillion (PPT) levels</li><li>Available in 5 cc (200 mg) configuration</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_Glass_Cartridges_5e96319c7f.jpg" alt="Waters: Oasis Glass Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_Glass_Cartridges_5e96319c7f.jpg 188w," sizes="100vw" width="409" height="339"></p><h5><strong>Oasis On-Line Columns and Cartridges</strong></h5><ul><li>For rugged, reproducible, and ultra-fast on-line analysis</li><li>Wide choice of configurations, particle sizes, and sorbent chemistries</li><li>Available with all six patented Oasis sorbents—PRiME HLB, HLB, MCX, MAX, WCX, and WAX</li><li>High recovery and reproducible results for a wide range of compounds</li><li>Cartridge format for use with Spark Holland Prospekt-2™/Symbiosis™ systems also available</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_On_Line_Columns_and_Cartridges_ba02114c92.jpg" alt="Waters: Oasis On-Line Columns and Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_On_Line_Columns_and_Cartridges_ba02114c92.jpg 168w," sizes="100vw" width="415" height="386"></p><h4><strong>Sample preparation, improved</strong></h4><p>Improving various aspects of chromatography and mass spectrometry analyses often starts with sample preparation. &nbsp;Solid-phase extraction (SPE) or "liquid-solid phase extraction" is a sample preparation technology that uses particles of chromatographic packing material, usually in a cartridge or 96-well plate format, to chemically separate different analytes and aid in removing matrix components in a sample. &nbsp;</p><p>SPE is a proven sample preparation tool for simple sample matrix removal, including common interferences like proteins, salts, fats and phospholipids. This matrix removal provides many benefits, including matrix effect reduction and an increase in sample concentration and analyte specificity. Matrix removal also significantly simplifies chromatographic complexity by reducing the number of interfering peaks in the LC and reducing signal suppression by providing clean samples for the MS.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_SPE_LC_MS_MS_chromatogram_of_1_pgm_L_of_alprazolam_from_rat_plasma_8b7275b25b.jpg" alt="Waters: Oasis SPE - LC-MS-MS chromatogram of 1 pgmL of alprazolam from rat plasma" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_SPE_LC_MS_MS_chromatogram_of_1_pgm_L_of_alprazolam_from_rat_plasma_8b7275b25b.jpg 169w," sizes="100vw" width="1024" height="946"></p><h4><strong>Get the cleanest extracts with the Oasis 2x4 method</strong></h4><p>Having a variety of tools for method development allows separation scientists to optimize protocols for maximum sensitivity and selectivity. The Oasis 2x4 method for SPE sorbent and protocol selection for acids, bases, and neutrals produces the cleanest extracts – all by eliminating matrix interferences and sample variability. Get the flexibility to extract acids, bases, and neutrals with high SPE recoveries while removing matrix components that may interfere with analysis with our two protocols and four sorbents. By following the simple steps outlined in the Oasis 2x4 method, you can achieve high recoveries and the cleanest extracts.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_2x4_protokol_pro_vyvoj_metody_c417be9006/Waters-Oasis-2x4-protokol-pro-vyvoj-metody.jpg" alt="Waters: Oasis SPE - Oasis 2 x 4 method development protocol." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_2x4_protokol_pro_vyvoj_metody_c417be9006/thumbnail_Waters-Oasis-2x4-protokol-pro-vyvoj-metody.jpg 242w," sizes="100vw" width="1519" height="979"></p><h4><strong>Isolate your compounds with the Oasis HLB method</strong></h4><p>Solid-phase extraction (SPE) method development starts with knowledge of the sample matrix—the nature and relative concentration of the analytes of interest and potentially interfering endogenous compounds. The right sorbent and solvents are selected for load, wash, and elute steps, resulting in the creation of rugged, reliable, and selective protocols. The Oasis HLB method is a generic protocol used to isolate a broad range of acidic, basic, and neutral compounds from a wide spectrum of matrices.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_SPE_Generic_Method_Protocol_with_Oasis_HLB_SPE_83d684704d.jpg" alt="Waters: Oasis SPE - Generic Method Protocol with Oasis HLB SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_SPE_Generic_Method_Protocol_with_Oasis_HLB_SPE_83d684704d.jpg 139w," sizes="100vw" width="1024" height="1153"></p><h4><strong>Multiple contaminant analysis with the 2-step pass-through protocol</strong></h4><p>If you are doing multiple residue screening of veterinary drugs, pesticides and mycotoxins in various food matrices, you may be facing a high concentration of organic solvents. With our simple 2-step protocol (pass-through SPE), you can remove matrix interferences quickly if your samples contain a high concentration of organic solvent(s) and concentration and/or salt removal is not required. It can be used as the clean-up method following QuEChERS extraction, saving you significant time compared to the traditional dispersive SPE method - all while achieving superior clean-up.</p><p><strong>To do pass-through SPE, Waters offers 2 convenient and flexible formats:</strong></p><ul><li><strong>Traditional-style cartridges</strong> compatible with vacuum and positive pressure manifolds&nbsp;</li><li><strong>"Plus" style cartridges</strong> that can be used without manifolds when connected to a displacement syringe</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_SPE_kolonky_3_b4da6242de/Waters-Oasis-SPE-kolonky-3.jpg" alt="Waters: Oasis Plus Light and Plus Short Cartridges for 2-step pass through protocol." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_SPE_kolonky_3_b4da6242de/thumbnail_Waters-Oasis-SPE-kolonky-3.jpg 152w," sizes="100vw" width="1308" height="1342"></p>

Products from category Consumables distributed by Waters Corporation (Europe) - page 1

Related content

Why Nitrogen Is Costing Labs More Than Ever — And How to Reduce the High Price Tag

News from LabRulezLCMS Library - Week 21, 2026

Let´s Connect a whole (U)HPLC system without tools and trouble