<p><strong>When performing analyte extraction with </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products?category=136&amp;manufacturerItems=50"><strong>SPE</strong></a><strong> we expect 100% recovery. If recovery is lower, this would suggest there is an issue with retrieval of the analyte from the sorbent. But what are some of the reasons you may see a recovery greater than what you were expecting (or over 100%)?</strong></p><h3><strong>Common problems</strong></h3><ul><li>Co-eluting interferences</li><li>Contaminants from the solvent or sorbents selected</li><li>Internal standard is compromised making your reference point inaccurate</li><li>Recovery calculations are inaccurate</li></ul><p><strong>Let's examine each of these common problems.</strong></p><h4><strong>Co-eluting interferences</strong></h4><p>These are typically present in the matrix and the goal of the SPE step is to remove them. If you are experiencing recoveries greater than 100%, the first step would be to <strong>check the eluent using an orthogonal analytical technique </strong>to identify that the increased recovery is a result of a co-elution.&nbsp;</p><p><strong>Where a co-elution is identified, there are a few possible solutions.</strong></p><ol><li><strong>Modify the wash steps of the SPE method </strong>to selectively remove the impurity during washing</li><li><strong>Select an alternative SPE sorbent </strong>which will better remove these impurities. This is easier if the analyte / impurity can be selectively ionized, as an ion-exchange sorbent will very often afford cleaner extracts than either reversed or normal phase solutions</li><li><strong>Adjust your analytical method</strong> to resolve the 2 peaks analytically, negating the necessity to remove this impurity during the SPE step.</li><li><strong>Run a blank plasma sample</strong>; this will allow you to ascertain the impurities present and use this blank in the calculations to subtract from your recovery</li></ol><h4><strong>Contaminants from the solvent or sorbent</strong></h4><p>These will typically be impurities present in the starting materials which are similar in nature to your compound of interest, and as a result co-elute with it during SPE and subsequent analytical analysis. You can <strong>follow the steps above to remove co-eluting impurities, or alternatively</strong> as this is not an impurity present in your matrix, you can identify the level present in the sorbent using blank runs and subtract this from your main peak during the calculation. Prior to addition of your sample if you equilibrate your sorbent with the elution solvent this should flush out potential contaminants from the sorbent. For impurities introduced from the solvent, typically switching the solvent should resolve this.</p><h4><strong>Internal standard is compromised</strong></h4><p>If your internal standard is not showing 100% recovery, your subsequent calculations will be inaccurate. It is always good practice to <strong>use an internal standard similar in nature to your compound of interest</strong> as this will give the more consistent reference point for your method.&nbsp;</p><p>If there is concern your internal standard is not showing good recovery from the SPE material using your method, you can use an <strong>external standard</strong> which is added to the elution solvent to calculate absolute recovery.</p><h4><strong>Recovery calculations are inaccurate</strong></h4><p>It is important to follow this step wise to ascertain where the errors are appearing.</p><ol><li>Calculation Errors - Check all calculations and account for all dilution factors</li><li>Integration Errors - Reintegrate all peaks and use manual calculations to confirm</li><li>Analytical method errors – Ensure the analytical method used allows correct integration and calculation. Ensure no strong solvents are used for injection and run a calibration across a number of dilutions to ensure linearity. Troubleshoot your analytical method to determine any factors which may lead to poor reproducibility</li><li>Ensure detections selected are appropriate and working correctly.</li></ol><p>We hope this tip was useful! Check out our resources on <a target="_blank" rel="noopener noreferrer" href="https://www.phenomenex.com/techniques/solid-phase-extraction"><strong>solid phase extraction</strong></a>. See you next month for another tip!</p>

Why are my recoveries greater than 100%?

<div><div><p><strong>A new paper from the group of </strong><a target="_blank" rel="noopener noreferrer" href="https://curtis.group.uochb.cz/en"><strong>Ed Curti</strong></a><strong>s at IOCB Prague in collaboration with the </strong><a target="_blank" rel="noopener noreferrer" href="https://pluskal.group.uochb.cz/en"><strong>Pluskal group</strong></a><strong> introduces a structure-guided way to explore nucleic acid sequence space that goes far beyond traditional random mutagenesis. By combining rational library design, single-round selections, high-throughput sequencing, and machine learning, the authors rapidly identified catalytically active variants of a fluorescent deoxyribozyme and elucidated predictive rules linking sequence to function. The study was published in the journal </strong><i><strong>Nucleic Acids Research</strong></i><strong>.</strong></p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_2_2eb701e572.jpeg" alt="IOCB Prague: Exploring sequence space beyond random mutagenesis" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_2_2eb701e572.jpeg 245w," sizes="100vw" width="2006" height="789"></p></div></div><div><p>Understanding how sequence determines function remains a central challenge in nucleic acid engineering. Conventional strategies typically rely on libraries generated by random mutagenesis of a single variant of a motif, which provide dense coverage close to the original sequence but little information about more distant variants. This limitation makes it difficult to uncover more general principles governing complex functional motifs such as catalytic nucleic acids.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_e1e7a30d1c.jpg" alt="IOCB Prague/Tomáš Belloň: Edward Curtis, head of the Functional Potential of Nucleic Acids group at IOCB Prague" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_IOCB_Prague_Exploring_sequence_space_beyond_random_mutagenesis_e1e7a30d1c.jpg 234w," sizes="100vw" width="1500" height="1001"></p><p>In a new study led by <strong>Edward A. Curtis</strong>, with <strong>Jaroslav Kurfürst</strong> and <strong>Martin Volek</strong> as the first authors, the researchers<strong> introduce a fundamentally different strategy</strong> for exploring sequence space that combines structure-informed library design, single-round selections, high-throughput sequencing, and machine learning. Instead of randomly mutating a single sequence, the team constructed a library composed of sequences that already satisfy multiple structural and functional constraints of a target motif. This approach was tested on Aurora, a fluorescent deoxyribozyme previously <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/article/4223"><strong>discovered</strong></a><strong> </strong>in the group.</p><p>The results indicate that this approach is a more efficient way to explore sequence space than standard approaches. A secondary structure library based on Aurora yielded approximately 40 times more unique catalytic sequences than a conventional randomly mutagenized library, and active variants could be rapidly identified in a single round of selection. High-throughput sequencing data were then used to train machine learning models, which successfully identified rules relating sequence to activity. Remarkably, these models could accurately predict read numbers and identify the most active variants using only small subsets of sequences for training.</p><p>By integrating rational library design with data-driven analysis, the study demonstrates a scalable way to explore nucleic acid sequence space more rapidly and comprehensively than standard methods allow. Beyond fluorescent deoxyribozymes, this framework provides a general blueprint for accelerating the discovery and optimization of functional nucleic acids, while simultaneously extracting predictive rules that link sequence to function.</p><blockquote><h5><strong>Read the paper</strong></h5><p>Kurfürst, J.; Volek, M.; Samusevich, R.; Pluskal, T.; Curtis, E. A. Using Structured Libraries, Selection, and Machine Learning to Rapidly Explore the Sequence Space of a Fluorescent Deoxyribozyme. <i>Nucleic Acids Res.</i> <strong>2025</strong>, 53 (22). <a target="_blank" rel="noopener noreferrer" href="https://doi.org/10.1093/nar/gkaf1348"><strong>https://doi.org/10.1093/nar/gkaf1348</strong></a></p></blockquote></div>

Exploring sequence space beyond random mutagenesis

<p><strong>Our Library never stops expanding. What are the most recent contributions to LabRulezLCMS Library in the week of 19th January 2026? Check out new documents from the field of liquid phase, especially HPLC and LC/MS techniques!</strong></p><blockquote><p><span style="font-size:20px;">👉 </span><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library"><span style="font-size:20px;"><strong>SEARCH THE LARGEST REPOSITORY OF DOCUMENTS ABOUT LCMS AND RELATED TECHNIQUES</strong></span></a></p></blockquote><blockquote><p><strong>👉 Need info about different analytical techniques?</strong> Peek into <a target="_blank" rel="noopener noreferrer" href="https://gcms.labrulez.com/library"><strong>LabRulezGCMS</strong></a> or <a target="_blank" rel="noopener noreferrer" href="https://icpms.labrulez.com/library"><strong>LabRulezICPMS</strong></a> libraries.</p></blockquote><p>This week we bring you application notes by <strong>Agilent Technologies, Shimadzu, Waters Corporation </strong>and poster by<strong> Thermo Fisher Scientific!</strong></p><h3><strong>1. Agilent Technologies: Automated Bioprocess Monitoring with Agilent 1290 Infinity III Bio Online LC Solutions</strong></h3><p><strong>Process analytics of L-alanine production using genetically modified </strong><i><strong>Vibrio natriegens</strong></i></p><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_automated_bioprocess_monitoring_1290_infinity_bioonline_solutions_5994_8865en_agilent_9f33de6ddf.pdf"><strong>Full PDF for download</strong></a></li></ul><p>Bioprocess engineering is a challenging field because of the constantly changing nature of bioprocess models which make them difficult to validate.1 Consequently, process control needs to be developed at various levels using strategies tailored to these specific requirements.1 The performance and effectiveness of the bioreactor are determined by key performance indicators such as product yield, titer, production rate, and quality of the product.1 These factors can be quickly influenced by changes in process variables and the raw materials used.1,2 The ability to react quickly to problems is therefore crucial for preserving ongoing production, a factor that can be particularly significant in bioprocesses due to the substantial cost and time investmented.1,2 Such challenges can be tackled by constantly monitoring the bioprocess, which requires the ability to analyze and collect data quickly. Therefore, monitoring is of the utmost importance.&nbsp;</p><p>This application note describes the advantages of using an Agilent 1290 Infinity III Bio Online LC solution with Agilent Online LC Monitoring software. A bioreactor was interfaced with a Flownamics Seg-Flow S3 sampling system for aseptic withdrawal and an Agilent 1290 Infinity III Bio Online LC to make an hourly analysis.&nbsp;</p><p>This is a fully automated approach for taking sterile samples from a bioreactor and preparing or diluting them. In addition, the 1290 Infinity III Bio Online LC solution displays data in near real time, which is a crucial element for effective bioprocess&nbsp;monitoring.</p><h4><strong>Experimental&nbsp;</strong></h4><h5><strong>Equipment&nbsp;</strong></h5><p>The <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=10&amp;search=1290+Infinity+III+Bio"><strong>1290 Infinity III Bio </strong></a>Online LC comprised the following&nbsp;modules:&nbsp;</p><ul><li>Agilent 1290 Infinity III Bio Flexible Pump (G7131A) with an InfinityLab Quick Change Bio inline filter assembly (part&nbsp;number 5067-1607), 2.1 mm id, 0.2 µm pore size&nbsp;</li><li>Agilent 1290 Infinity III Bio Online Sample Manager (G3167B) with Sample Thermostat (option #101) clustered with Agilent 1290 Infinity Valve Drive (G1170A), featuring a reactor valve pod (part number 5067-6680) and Online LC Monitoring Software&nbsp;</li><li>Agilent 1290 Infinity III Multicolumn Thermostat (G7116B) equipped with an Agilent Quick Connect Bio Heat Exchanger Std. (G7116-60071)&nbsp;</li><li>Agilent 1290 Infinity III Diode Array Detector (DAD) (G7117B), equipped with a Bio Max-Light Cartridge Cell (G4212-6008), 10 mm, 1 µL&nbsp;</li><li>Agilent 1260 Infinity High-Performance Degasser (G4225A) is connected between S1 (transport solvent) solvent line and Agilent 1290 Infinity III Bio Online Sample Manager (G3167B)&nbsp;</li></ul><h5><strong>Software&nbsp;</strong></h5><ul><li>Agilent <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=10&amp;search=OpenLab+CDS"><strong>OpenLab CDS</strong></a> version 2.8 or later versions&nbsp;</li><li>Agilent Online LC Monitoring Software version 1.3 or later&nbsp;versions&nbsp;</li><li>Flownamics FlowWeb control&nbsp;software</li></ul><h5><strong>Instrumental configuration&nbsp;</strong></h5><p>The 1290 Infinity III Bio Online LC solution was used with a Seg-Flow interface for automatic sampling and online analysis (see Figure 1). The Seg-Flow interface was used to withdraw samples from a bioreactor through a Flownamics F-Series 310 FISP probe with a ceramic membrane filter (0.2&nbsp;µm pore size) from a 5 L bioreactor. The drawn samples were sent through the built-in sample collection cup on the Seg‑Flow to the LC and the samples were retained into vials. The collected samples were then automatically derivatized by using an injector program and subsequently analyzed. A more detailed description of the instrumental configuration has been published.<sup>3</sup></p><h4><strong>Conclusion&nbsp;</strong></h4><p>For online bioprocess monitoring, a fully automated setup consisting of a bioreactor, a Flownamics sampling system, and an Agilent 1290 Infinity III Bio Online LC solution was successfully established. This setup is capable of taking aseptic samples from a bioreactor, preparing, analyzing, and processing samples without the need for manual interaction. In addition, the added value of the Agilent Online LC Monitoring software was evident in the display method and the ability to track it quickly.</p><h3><strong>2. Shimadzu: Analysis of Oligonucleotide Impurities Using Single Quadrupole Mass Spectrometer</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/an_01_00974_en_c50bb67c7a.pdf"><strong>Full PDF for download</strong></a></li></ul><h4><strong>User Benefits</strong></h4><ul><li>Combination use of LCMS-2050 single quadrupole mass spectrometer and LabSolutions Insight Biologics provides comprehensive characterization of oligonucleotides and related impurities.</li><li>Purity calculations for target components can be performed even on poorly separated peaks by utilizing MS spectra simultaneously acquired with UV chromatogram.</li></ul><p>In recent years, oligonucleotide therapeutics have been paid attention as a novel drug discovery modality because of their rapid progress of development. During the synthesis of oligonucleotide therapeutics, impurities that have differing base chain lengths are generated along with the target oligonucleotide. To ensure the safety and efficacy of the drug, comprehensive detection and identification of these impurities are required.&nbsp;</p><p>Reversed phase ion-pair chromatography is often employed as a method to separate the target compound from co-existing impurities. However, it is often difficult to establish analytical conditions that provide compete separation of all impurities that are formed in synthesis process due to their similar structures and properties to the principal compound of active ingredient. Against this drawback, liquid chromatography-mass spectrometry (LC-MS) is commonly used for impurity detection and identification. For analysis of oligonucleotide impurities, quadrupole time-of-flight mass spectrometers are mainly used because of their high mass resolution and ability to perform sequence and structure estimations via MS/MS analysis. However, in quality control process, the use of a single quadrupole mass spectrometer is expected to be advantageous because of providing mass information with easy operation when impurity information is already known.&nbsp;</p><p>This article presents a simulated impurity analysis of synthetic oligonucleotide using the LCMS-2050 high-performance liquid chromatography-mass spectrometer and LabSolutions Insight Biologics.</p><h4><strong>Analytical conditions</strong></h4><p>The employed instrument setup was <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=1&amp;search=Nexera+XS"><strong>Nexera XS inert</strong></a> and <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=1&amp;search=LCMS-2050"><strong>LCMS-2050</strong></a>. HPLC conditions are shown in Table 2, and MS conditions are shown in Table 3. The conditions were set where n-1(5') co-eluted with FLP, while n-3(5') was separated (Fig. 1) to demonstrate impurity analysis performance.</p><h4><strong>Conclusion</strong></h4><p>The simulated sample consisting of mainly FLP and small amounts of n-1(5')/n-3(5') was analyzed using the LCMS-2050 and LabSolutions Insight Biologics software and obtained data were processed appropriately. Detection, identification, and quantitation at low concentrations were accomplished not only for n-3(5') well-separated from FLP but also for n-1(5') co-eluted with FLP. In case that establishing analytical conditions is difficult, Using this instrument setup and software will provide efficient quality confirmation of oligonucleotide therapeutics.</p><h3><strong>3. Thermo Fisher Scientific: Simultaneous Quantitation and Untargeted Discovery (SQUAD) workflow using multiple fragmentation techniques for quantitation and characterization of trace level nitrosamine in biological matrices</strong></h3><ul><li>Poster</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/po_squad_workflow_multiple_fragmentation_techniques_po_en_94a5b27b12.pdf"><strong>Full PDF for download</strong></a></li></ul><p>N-Nitrosamines are a class of carcinogenic chemical compounds that pose threat to humans exogenously through matrices like drinking water, food, cosmetics, and endogenously by nitrosation in gastrointestinal tract, nitrate to nitrite conversion, etc. An accurate, reliable analytical method is critical for detection and quantification of these trace-level, polar and low molecular weight compounds to understand the association between their exposure and related diseases.&nbsp;</p><p>An optimized SQUAD workflow is presented that discovers unknown compounds in the matrix by using high resolution orbitrap and a sensitive linear ion trap detector that quantifies the low intensity nitrosamines in a single run. The workflow uses multiple fragmentation types – HCD, CID and UVPD and MSn to help characterize isomeric structures.</p><h4><strong>Methods</strong></h4><p>Serial dilution of Nitrosamine standards were subjected to Simultaneous Quantitation and Discovery (SQUAD) analysis using <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/744"><strong>Thermo Scientific™ Vanquish™ Horizon UHPLC system</strong></a> and the <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/561"><strong>Thermo Scientific™ Orbitrap IQ-X™ Tribrid™ mass spectrometer</strong></a> . Nitrosamine spiked matrices of human pooled urine and human Serum were subjected to SQUAD analysis.</p><h4><strong>Data Analysis&nbsp;</strong></h4><p>Spectra were evaluated for nitrosamines using Thermo Scientific™ FreeStyle™ software and annotated using Thermo Scientific™ <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1757"><strong>Mass Frontier™ 8.0 software</strong></a>. Untargeted data analysis was performed using <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1759"><strong>Compound Discoverer 3.4 software</strong></a>. Calibration curves were generated using Thermo Scientific™ <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/77"><strong>TraceFinder™ 5.2 software</strong></a>.</p><h4><strong>Conclusions&nbsp;</strong></h4><ul><li>Detection limits as low ppb levels ( 0.2 ppb –0.5 ppb) and quantitation limits (0.2 ppb- 5 ppb ) in presence of the matrix were achieved for all seven nitrosamines by applying parallel ion trap analysis&nbsp;</li><li>SQUAD analysis was run on Orbitrap IQ-X Tribrid MS and achieved low ppb level quantitation in ion trap and identified unknown compounds through discovery analysis in Orbitrap.&nbsp;</li><li>Employing nano LC helped achieve lower limit of quantitation (5 ppt)</li></ul><h3><strong>4. Waters Corporation: Validated LC-MS/MS Method for Vitamin E Acetate in Cannabis Plants and Derived Products</strong></h3><ul><li>Application note</li><li><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/labrulez-bucket-strapi-h3hsga3/720009082_en_c7a6fc6190.pdf"><strong>Full PDF for download</strong></a></li></ul><h5><strong>Benefits&nbsp;</strong></h5><ul><li>The validated LC-MS/MS method provides high sensitivity and specificity for VEA quantification in complex cannabis matrices, including flower and concentrates.&nbsp;</li><li>Minimal sample preparation reduces handling time and improves laboratory throughput, supporting efficient routine analysis.&nbsp;</li><li>The method demonstrates robust performance across multiple matrices, ensuring reliable detection even in lipid-rich, chemically diverse samples.</li><li>Use of Waters ACQUITY UPLC H-Class System and Xevo TQ-S micro Mass Spectrometer enables accurate quantitation well below regulatory requirements.&nbsp;</li><li>The validated method complies with Missouri DCR and DHSS regulatory limits, enabling laboratories to confidently monitor VEA in cannabis products.</li></ul><p>VEA is used as a diluent and viscosity modifier in certain cannabis-derived products, including vaping formulations. Following increased public health awareness during 2019, VEA became a marker of interest for quality control and regulatory surveillance across cannabis supply chains due to its potential impact on lung health. In addition to concentrates and vape liquids, trace residues may be present in infused products and processing intermediates. Therefore, reliable quantification of VEA in these chemically diverse, lipid-rich matrices requires an analytical method that is sensitive, selective, and robust against matrix effects. In February 2024, Missouri’s DCR revised the tolerance limit for VEA in cannabis products from 0.2 ppm to 5 ppm.<sup>1&nbsp;</sup></p><p>Liquid chromatography coupled with tandem quadrupole mass spectrometry (LC-MS/MS) provides the sensitivity and specificity required to distinguish VEA from endogenous cannabinoids, terpenes, and other lipophilic excipients, while also offering the sensitivity to support low-ppm and sub-ppm action limits. Unlike UVbased methods, where co-eluting chromophores may interfere, LC-MS/MS enables targeted multiple reaction monitoring (MRM) for confident identification and accurate quantitation in complex cannabis matrices.&nbsp;</p><p>This application note describes the validation of an LC-MS/MS method for the quantitation of VEA in two inhalable products, cannabis flower and cannabis concentrates. The method was developed and validated using the Waters ACQUITY UPLC H-Class System coupled with a Xevo TQ-S micro Triple Quadrupole Mass Spectrometer. Chromatographic separation was achieved with a reversed-phase ACQUITY UPLC BEH C18 Column. A streamlined sample preparation approach was applied for cannabis flowers and concentrates, which minimizes handling time and increases sample throughput.&nbsp;</p><p>The validation study was conducted at GPA. Method performance was evaluated for calibration range, linearity, LOD, LOQ, accuracy, precision, recovery, repeatability, and robustness. The results of these are evaluated against acceptance criteria set by State of Missouri DHSS and presented in this application note.</p><h4><strong>Experimental&nbsp;</strong></h4><ul><li><strong>LC system: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/198"><strong>ACQUITY UPLC H-Class Plus System&nbsp;</strong></a></li><li><strong>MS detection: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/209"><strong>Xevo TQ-S micro Mass Spectrometer&nbsp;</strong></a></li><li><strong>Column: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/1952"><strong>ACQUITY UPLC BEH C18 Column</strong></a>, 2.1 x 50 mm, 1.7 µm (p/n: 186002350)</li><li><strong>Software:</strong> <a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/products/635"><strong>MassLynx™ 4.1 Software&nbsp;</strong></a></li><li><strong>Data processing: </strong><a target="_blank" rel="noopener noreferrer" href="https://lcms.labrulez.com/library?mainauthorItems=5&amp;search=TargetLynx"><strong>TargetLynx™</strong></a> Application</li></ul><h4><strong>Conclusion&nbsp;</strong></h4><p>The LC-MS/MS method developed and validated for VEA quantification in cannabis flower and concentrates demonstrates excellent linearity, accuracy, precision, and robustness, and meets the regulatory requirements. Calibration curves achieved R² values greater than 0.999, with LOD and LOQ well below the Missouri action limit of 5 ppm. Matrix-spiked recoveries across flower and concentrate samples were within the 70–130% acceptance range, and QC samples met all performance criteria, confirming method reliability. Robustness testing across analysts and matrices further validated the method’s reproducibility. Overall, this approach provides a streamlined, sensitive, and regulatory-compliant workflow for laboratories, enabling accurate monitoring of VEA to support quality control, consumer safety, and regulatory compliance in cannabis-derived products</p>

News from LabRulezLCMS Library - Week 04, 2026

Article

Application

Academy

Scientific article

Science and research

Poster

The Institute of Organic Chemistry and Biochemistry of the Czech Academy of Sciences (IOCB Prague) is a leading scientific institution in the Czech Republic, recognized internationally. Its primary mission is basic research in the fields of chemical biology and medicinal chemistry, organic and material oriented chemistry, chemistry of natural compounds, biochemistry and molecular biology, physical chemistry, theoretical chemistry, and analytical chemistry. 

Institute of Organic Chemistry and Biochemistry of the Czech Academy of Sciences

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

Thermo Scientific SureSTART Vials and Well Plates Collection

Start your analysis with confidence using SureSTART vials, caps, well plates, and kits—offering full compatibility, quality materials, and performance across three levels.

<h4><strong>Streamlined choice. Trusted quality.</strong></h4><p><strong>Start your analysis with confidence using Thermo Scientific™ SureSTART™ vials, caps, inserts, well plates, mats, and certified kits designed to meet your analytical, regulatory, and performance requirements. With full instrument compatibility, high material quality, and consistent performance across three defined levels, the SureSTART collection offers a smarter way to choose the right sample containment solution for your workflow.</strong></p><h3><strong>Why choose SureSTART?</strong></h3><ul><li><strong>Proven reliability</strong>: Every product is manufactured and certified to meet physical specifications—no weak links in your workflow.</li><li><strong>Clear selection</strong>: Three performance levels help you balance sensitivity, robustness, and cost, now visually marked with one, two, or three waves on the vial.</li><li><strong>Universal compatibility</strong>: Designed for seamless integration with all major GC, HPLC/UHPLC, and MS autosamplers across all vendors.</li><li><strong>Certified cleanliness</strong>: Products are manufactured using the purest glass and plastics with low extractables and leachables, including GOLD-grade and silanized glass.</li><li><strong>Maximum sample integrity</strong>: Minimize analyte loss and background peaks with precision-engineered sealing, surface chemistry, and material composition.</li><li><strong>Bulk savings &amp; simplified inventory</strong>: Available in multiple pack sizes, performance levels, and formats to support your lab’s needs and budget.</li></ul><h3><strong>The Three Performance Levels</strong></h3><ul><li><strong>Level 1 – Everyday analysis</strong>: For general-purpose GC/HPLC detection (e.g. UV/Vis, FID, RI). These chromatography-approved products are ideal for routine analyses with cost-efficiency in mind.</li><li><strong>Level 2 – High-throughput analysis</strong>: Designed for regulated labs requiring robust and reproducible data, especially when using MS detectors for routine quantification.</li><li><strong>Level 3 – High performance</strong>: For the most sensitive and selective analyses near the method detection limit. Packed in cleanroom environments and made with ultra-pure materials for maximum sample security and MS compatibility.</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Sure_START_Vials_and_Well_Plates_Collection_5a8b0da936.jpg" alt="Thermo Scientific SureSTART Vials and Well Plates Collection: Three performance levels help you balance sensitivity, robustness, and cost, now visually marked with one, two, or three waves on the vial." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Sure_START_Vials_and_Well_Plates_Collection_5a8b0da936.jpg 245w," sizes="100vw" width="1182" height="270"></p><h3><strong>SureSTART Certified Vial and Cap Kits</strong></h3><ul><li><strong>Specification Certified</strong>: Routine analyses – Certified for physical specifications; no individual certificate.</li><li><strong>LC/GC Certified</strong>: Chromatography-grade – Tested for 15 physical parameters with LC-UV &amp; GC-FID; certificate included.</li><li><strong>MSCERT</strong>: For LC-MS/GC-MS – Certified low-adsorption kits tested with MS; includes SureStop™ vials with AVCS™ caps.</li><li><strong>MSCERT+</strong>: For trace-level MS or DIA – Pre-cleaned, tested with LC-MS/GC-MS, and sold only as kits to ensure purity.</li><li><strong>Application Certified</strong>: Pre-matched kits for specific instruments or validated applications.</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Sure_START_Vials_and_Well_Plates_Collection_2_fef6049d71.jpg" alt="Thermo Scientific SureSTART Vials and Well Plates Collection: There are several factors to consider when choosing a vial or well plate for your application. The table below will help guide you through this process to determine what type of product/performance level is most suitable for your application requirements." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Sure_START_Vials_and_Well_Plates_Collection_2_fef6049d71.jpg 204w," sizes="100vw" width="1515" height="1159"></p><h3><strong>SureSTART Well Plates and Mats</strong></h3><p>Thermo Scientific™ WebSeal™ well plates are ideal for laboratories seeking to increase autosampler capacity, reduce solvent usage, and streamline high-throughput workflows. Available in <strong>96- and 384-well formats</strong>, they offer a certified alternative to traditional vials and are fully compatible with automated SPE/SLE platforms.</p><ul><li><strong>Space-saving efficiency</strong>: Replace vials with well plates to increase sample capacity up to 8× and reduce storage footprint.</li><li><strong>Flexible performance levels</strong>:<ul><li><strong>Level 1: Standard plates for routine</strong>, non-regulated use (GC-tested).</li><li><strong>Level 2: Low-bleed plates and high-performance mats</strong>, validated for LC-MS/GC-MS.</li><li><strong>Level 3: Premium WebSeal Plate+</strong> with glass-coated plastic wells—ideal for trace analytes and protein adsorption control.</li></ul></li><li><strong>Solvent stability and clean sample contact</strong>: WebSeal Plate+ uses nanolayered silicon dioxide for minimal extractables and ultra-low adsorption.</li><li><strong>Compatible sealing options</strong>:<ul><li><strong>Silicone mats: </strong>For long-term storage and consistent results.</li><li><strong>Pre-slit mats: </strong>For autosampler injection without evaporation or contamination.</li><li><strong>Adhesive seals: </strong>For single-use workflows and re-sealing options with cavity protection.</li></ul></li></ul><p>Whether you work with polar solvents, proteins, or trace-level analyses, SureSTART well plates and sealing accessories help you optimize throughput, precision, and data confidence across all chromatography workflows.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Sure_START_Vials_and_Well_Plates_Collection_3_abce3dd960.jpg" alt="Thermo Scientific SureSTART Vials and Well Plates Collection: Selecting the perfect Thermo Scientific WebSeal well plates and mats for your chromatography requirements is easy using our selector tools and resources." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Sure_START_Vials_and_Well_Plates_Collection_3_abce3dd960.jpg 245w," sizes="100vw" width="1516" height="902"></p>

Waters Oasis SPE products

Waters Oasis SPE products come in a broad range of sorbents and an array of formats. With Oasis products, you can meet a wide variety of sample preparation needs.

<h4><strong>Faster, cleaner, and simpler SPE starts here</strong></h4><p>Analytical chemists worldwide use SPE to remove interfering matrix compounds and enrich the analyte of interest to ensure the generation of high-quality data.</p><p>Waters Oasis SPE products come in a broad range of sorbents and an array of formats. With Oasis products, you can meet a wide variety of sample preparation needs, from simple and fast sample matrix clean-up to more complex sample preparation challenges.</p><p>Oasis SPE products deliver unmatched purity, consistency, and quality for sample analysis. Along with seven different SPE chemistries, Oasis SPE products use universal to customized protocols to handle your unique sample.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_SPE_kolonky_2_967d461f2e/Waters-Oasis-SPE-kolonky-2.jpg" alt="Waters: Oasis SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_SPE_kolonky_2_967d461f2e/thumbnail_Waters-Oasis-SPE-kolonky-2.jpg 245w," sizes="100vw" width="950" height="416"></p><h4><strong>Overview</strong></h4><ul><li>Fully water-wettable sorbents increase reproducibility and enable elimination of condition and equilibration steps</li><li>Co-polymer pH stable from 0–14 with no secondary silanol activity</li><li>Optimal sensitivity for small molecule and therapeutic peptide analysis</li><li>Reduced matrix effects for LC-MS/MS analyses</li><li>Unsurpassed selectivity</li><li>Consistent retention and capacity, yielding the highest SPE recovery</li><li>Reduces variability in analytical results and increases robustness of analysis</li><li><strong>Recommended Use: </strong>For the fastest, cleanest, and simplest approach to SPE-LC-MS/MS method development.</li></ul><h4><strong>Solid-Phase Extraction Chemistries</strong></h4><h5><strong>Oasis PRiME HLB</strong></h5><ul><li>Multi-purpose hydrophilic-lipophilic balanced reversed phase sorbent for acids, bases, and neutrals</li><li>Cleaner samples in fewer steps with simple three-and two-step protocols, no SPE expertise required</li><li>Removes 95% of common matrix interferences, such as proteins, salts, phospholipids, and pigments</li><li>No sorbent conditioning or equilibration steps required</li><li>Faster, more predictable analysis time</li><li>Ideal for reversed-phase SPE clean-up of samples in routine analysis.</li></ul><h5><strong>Oasis PRiME MCX</strong></h5><ul><li>Mixed-mode Cation eXchange sorbent to selectively retain, concentrate and elute basic compounds</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Cleaner samples in fewer steps with simple and fast 3 and 4-step protocols</li><li>Removes 99% of phospholipids from complex sample matrices</li><li>No sorbent conditioning or equilibration steps required</li><li>Faster, more predictable analysis time</li><li>Highly reproducible target analyte recoveries</li><li>Ideal for basic compound specificity while removing matrix interferences in a simple clean-up.</li></ul><h5><strong>Oasis HLB</strong></h5><ul><li>Multi-purpose hydrophilic-lipophilic balanced reversed phase sorbent</li><li>Provides high capacity for acids, bases, and neutrals</li><li>Ideal for ultra-high capacity of very polar compounds.</li></ul><h5><strong>Oasis MCX</strong></h5><ul><li>Mixed-mode Cation eXchange sorbent for bases</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for selective retention of basic analytes.</li></ul><h5><strong>Oasis MAX</strong></h5><ul><li>Mixed-mode Anion eXchange for acids</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for selective retention of acidic analytes.</li></ul><h5><strong>Oasis WAX</strong></h5><ul><li>Weak Anion eXchange mixed-mode sorbent for strong acidic compounds</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for improved retention of strong acidic compounds.</li></ul><h5><strong>Oasis WCX</strong></h5><ul><li>Weak Cation eXchange mixed-mode sorbent for strong basic compounds</li><li>Increased analyte specificity and sensitivity</li><li>Reversed-phase and ion-exchange functionality for orthogonal sample preparation</li><li>Ideal for improved retention of all basic analytes, especially strong bases.</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Sorbenty_Oasis_SPE_na_bazi_kopolymeru_Oasis_HLB_c8ffee39b3/Waters-Sorbenty-Oasis-SPE-na-bazi-kopolymeru-Oasis-HLB.png" alt="Waters: Oasis Sorbents" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Sorbenty_Oasis_SPE_na_bazi_kopolymeru_Oasis_HLB_c8ffee39b3/thumbnail_Waters-Sorbenty-Oasis-SPE-na-bazi-kopolymeru-Oasis-HLB.png 211w," sizes="100vw" width="1511" height="1119"></p><h4><strong>Oasis Formats</strong></h4><h5><strong>Oasis μElution Plate</strong></h5><ul><li>Patented μElution plate design</li><li>No evaporation and reconstitution necessary due to elution volumes as low as 25 µL</li><li>Ideal for SPE clean-up and analyte enrichment of small sample volumes</li><li>Compatible with most liquid-handling robotic systems for automated, reliable high-throughput SPE (HT-SPE)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_m_Elution_Plate_aa7e36a4c1.jpg" alt="Waters: Oasis µElution Plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_m_Elution_Plate_aa7e36a4c1.jpg 245w," sizes="100vw" width="502" height="260"></p><h5><strong>Oasis 96-Well Sample Extraction Plates</strong></h5><ul><li>Innovative, award-winning two-stage well design</li><li>High throughput and high recovery</li><li>Compatible with most liquid-handling robotic systems for automated, reliable high-throughput SPE (HT-SPE)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_96_Well_Sample_Extraction_Plates_9528d532b9.jpg" alt="Waters: Oasis 96-Well Sample Extraction Plates" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_96_Well_Sample_Extraction_Plates_9528d532b9.jpg 245w," sizes="100vw" width="525" height="329"></p><h5><strong>Oasis Syringe-Barrel Cartridges</strong></h5><ul><li>Ultra-clean syringe barrel and frits</li><li>Available in cartridges ranging from 1 cc to 60 cc</li><li>Flangeless syringe-barrel cartridges available in 1 cc, 3 cc, and 6 cc sizes</li><li>Plus-style cartridges with Luer inlet hub and outlet tip, compatible with hand-held syringes</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_Syringe_Barrel_Cartridges_961aa06b8a.jpg" alt="Waters Corporation: Oasis Syringe-Barrel Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_Syringe_Barrel_Cartridges_961aa06b8a.jpg 245w," sizes="100vw" width="503" height="311"></p><h5><strong>Oasis Glass Cartridges</strong></h5><ul><li>Ultra-clean glass syringe with Teflon® frit</li><li>For trace level detection and analysis at part-per-trillion (PPT) levels</li><li>Available in 5 cc (200 mg) configuration</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_Glass_Cartridges_5e96319c7f.jpg" alt="Waters: Oasis Glass Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_Glass_Cartridges_5e96319c7f.jpg 188w," sizes="100vw" width="409" height="339"></p><h5><strong>Oasis On-Line Columns and Cartridges</strong></h5><ul><li>For rugged, reproducible, and ultra-fast on-line analysis</li><li>Wide choice of configurations, particle sizes, and sorbent chemistries</li><li>Available with all six patented Oasis sorbents—PRiME HLB, HLB, MCX, MAX, WCX, and WAX</li><li>High recovery and reproducible results for a wide range of compounds</li><li>Cartridge format for use with Spark Holland Prospekt-2™/Symbiosis™ systems also available</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_On_Line_Columns_and_Cartridges_ba02114c92.jpg" alt="Waters: Oasis On-Line Columns and Cartridges" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_On_Line_Columns_and_Cartridges_ba02114c92.jpg 168w," sizes="100vw" width="415" height="386"></p><h4><strong>Sample preparation, improved</strong></h4><p>Improving various aspects of chromatography and mass spectrometry analyses often starts with sample preparation. &nbsp;Solid-phase extraction (SPE) or "liquid-solid phase extraction" is a sample preparation technology that uses particles of chromatographic packing material, usually in a cartridge or 96-well plate format, to chemically separate different analytes and aid in removing matrix components in a sample. &nbsp;</p><p>SPE is a proven sample preparation tool for simple sample matrix removal, including common interferences like proteins, salts, fats and phospholipids. This matrix removal provides many benefits, including matrix effect reduction and an increase in sample concentration and analyte specificity. Matrix removal also significantly simplifies chromatographic complexity by reducing the number of interfering peaks in the LC and reducing signal suppression by providing clean samples for the MS.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_SPE_LC_MS_MS_chromatogram_of_1_pgm_L_of_alprazolam_from_rat_plasma_8b7275b25b.jpg" alt="Waters: Oasis SPE - LC-MS-MS chromatogram of 1 pgmL of alprazolam from rat plasma" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_SPE_LC_MS_MS_chromatogram_of_1_pgm_L_of_alprazolam_from_rat_plasma_8b7275b25b.jpg 169w," sizes="100vw" width="1024" height="946"></p><h4><strong>Get the cleanest extracts with the Oasis 2x4 method</strong></h4><p>Having a variety of tools for method development allows separation scientists to optimize protocols for maximum sensitivity and selectivity. The Oasis 2x4 method for SPE sorbent and protocol selection for acids, bases, and neutrals produces the cleanest extracts – all by eliminating matrix interferences and sample variability. Get the flexibility to extract acids, bases, and neutrals with high SPE recoveries while removing matrix components that may interfere with analysis with our two protocols and four sorbents. By following the simple steps outlined in the Oasis 2x4 method, you can achieve high recoveries and the cleanest extracts.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_2x4_protokol_pro_vyvoj_metody_c417be9006/Waters-Oasis-2x4-protokol-pro-vyvoj-metody.jpg" alt="Waters: Oasis SPE - Oasis 2 x 4 method development protocol." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_2x4_protokol_pro_vyvoj_metody_c417be9006/thumbnail_Waters-Oasis-2x4-protokol-pro-vyvoj-metody.jpg 242w," sizes="100vw" width="1519" height="979"></p><h4><strong>Isolate your compounds with the Oasis HLB method</strong></h4><p>Solid-phase extraction (SPE) method development starts with knowledge of the sample matrix—the nature and relative concentration of the analytes of interest and potentially interfering endogenous compounds. The right sorbent and solvents are selected for load, wash, and elute steps, resulting in the creation of rugged, reliable, and selective protocols. The Oasis HLB method is a generic protocol used to isolate a broad range of acidic, basic, and neutral compounds from a wide spectrum of matrices.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Corporation_Oasis_SPE_Generic_Method_Protocol_with_Oasis_HLB_SPE_83d684704d.jpg" alt="Waters: Oasis SPE - Generic Method Protocol with Oasis HLB SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Corporation_Oasis_SPE_Generic_Method_Protocol_with_Oasis_HLB_SPE_83d684704d.jpg 139w," sizes="100vw" width="1024" height="1153"></p><h4><strong>Multiple contaminant analysis with the 2-step pass-through protocol</strong></h4><p>If you are doing multiple residue screening of veterinary drugs, pesticides and mycotoxins in various food matrices, you may be facing a high concentration of organic solvents. With our simple 2-step protocol (pass-through SPE), you can remove matrix interferences quickly if your samples contain a high concentration of organic solvent(s) and concentration and/or salt removal is not required. It can be used as the clean-up method following QuEChERS extraction, saving you significant time compared to the traditional dispersive SPE method - all while achieving superior clean-up.</p><p><strong>To do pass-through SPE, Waters offers 2 convenient and flexible formats:</strong></p><ul><li><strong>Traditional-style cartridges</strong> compatible with vacuum and positive pressure manifolds&nbsp;</li><li><strong>"Plus" style cartridges</strong> that can be used without manifolds when connected to a displacement syringe</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Waters_Oasis_SPE_kolonky_3_b4da6242de/Waters-Oasis-SPE-kolonky-3.jpg" alt="Waters: Oasis Plus Light and Plus Short Cartridges for 2-step pass through protocol." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Waters_Oasis_SPE_kolonky_3_b4da6242de/thumbnail_Waters-Oasis-SPE-kolonky-3.jpg 152w," sizes="100vw" width="1308" height="1342"></p>

Phenomenex Strata X-AW Solid Phase Extraction (SPE)

Strata-X-AW mixed-mode SPE sorbent enables strong retention of acids (pKa ≤5) with 100% organic wash, ensuring maximum removal of interferences for clean, reliable extractions.

<p><strong>Weak Anion Mixed-Mode Solid Phase Extraction (SPE)</strong></p><p>A weak anion-exchange functionalized polymeric sorbent that allows for complete retention of acidic compounds with a <strong>pKa less than 5</strong>, making <strong>100% organic wash conditions possible</strong>. A 100% organic wash ensures that the maximum amount of interferences are removed from the target compound.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_AW_SPE_cd5908db4d.jpg" alt="Phenomenex: Strata-X-AW SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_AW_SPE_cd5908db4d.jpg 245w," sizes="100vw" width="500" height="268"></p><ul><li><strong>Recommended Use: </strong>Extraction of acidic compounds, particularly strong acids</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>For Acids with pKa ≤ 5</strong></h5><ul><li><strong>Column: </strong>1 mL Methanol</li><li><strong>Equilibrate: </strong>1 mL Water, pH 6-7</li><li><strong>Load: </strong>Diluted Sample pH 6-7</li><li><strong>Wash 1: </strong>1 mL 25 mM Ammonium Acetate Buffered, pH 6-7</li><li><strong>Wash 2: </strong>1 mL Methanol</li><li><strong>Elute Any Acid: </strong>2x 500 µL 5 % NH<sub>4</sub>OH in Methanol</li><li><strong>Elute Weak Acids: </strong>2x 500 µL 5 % Formic Acid in Methanol</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_single_tube_435d45d0ad.jpg" alt="Phenomenex: Strata X single tube" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_single_tube_435d45d0ad.jpg 156w," sizes="100vw" width="1080" height="1080"></p><p><i>Based on 30 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</i></p><h4><strong>Available Formats</strong></h4><ul><li><strong>96-Well-Plate</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_96_well_plate_9a66005814.jpg" alt="Phenomenex: Strata X 96-well plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_96_well_plate_9a66005814.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>1, 3, and 6mL Tubes</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg" alt="Phenomenex: Strata X 1, 3, and 6mL Tubes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>Giga Tubes (12-150mL Tubes)</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg" alt="Phenomenex: Strata X Giga Tubes (12-150mL Tubes)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg 156w," sizes="100vw" width="1080" height="1080"></p>

Phenomenex Strata X-A Solid Phase Extraction (SPE)

Strata-X-A strong anion-exchange SPE retains weak acids (pKa >2) with 100% organic wash, maximizing interference removal. Available in tubes, plates, and giga formats.

<p><strong>Strong Anion Mixed-Mode Solid Phase Extraction (SPE)</strong></p><p>A strong anion-exchange functionalized polymeric sorbent that allows for complete retention of weakly acidic compounds with a <strong>pKa greater than 2</strong>, making <strong>100% organic wash conditions possible</strong>. A 100% organic wash ensures that the maximum amount of interferences are removed from the target compound.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_A_SPE_e107f0b6bf.jpg" alt="Phenomenex: Strata-X-A SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_A_SPE_e107f0b6bf.jpg 245w," sizes="100vw" width="500" height="268"></p><ul><li><strong>Recommended Use: </strong>Extraction of weakly acidic compounds</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>For Acids with pKa &gt; 2</strong></h5><ul><li><strong>Column: </strong>1 mL Methanol</li><li><strong>Equilibrate: </strong>1 mL Water, pH 6-7</li><li><strong>Load: </strong>Diluted Sample pH 6-7</li><li><strong>Wash 1: </strong>1 mL 25 mM Ammonium Acetate Buffered, pH 6-7</li><li><strong>Wash 2: </strong>1 mL Methanol (collect this fraction to analyze Neutral/Bases)</li><li><strong>Elute Acid: </strong>2x 500 µL 5 % Formic Acid in Methanol</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_single_tube_435d45d0ad.jpg" alt="Phenomenex: Strata X single tube" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_single_tube_435d45d0ad.jpg 156w," sizes="100vw" width="1080" height="1080"></p><p><i>Based on 30 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</i></p><h4><strong>Available Formats</strong></h4><ul><li><strong>96-Well-Plate</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_96_well_plate_9a66005814.jpg" alt="Phenomenex: Strata X 96-well plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_96_well_plate_9a66005814.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>1, 3, and 6mL Tubes</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg" alt="Phenomenex: Strata X 1, 3, and 6mL Tubes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>Giga Tubes (12-150mL Tubes)</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg" alt="Phenomenex: Strata X Giga Tubes (12-150mL Tubes)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg 156w," sizes="100vw" width="1080" height="1080"></p>

Phenomenex Strata X-C Solid Phase Extraction (SPE)

Strata-X-C strong cation-exchange SPE retains basic compounds (pKa ≤10.5) with 100% organic wash for maximum cleanup. Offered in tubes, plates, and giga formats.

<p><strong>Strong Cation Mixed-Mode Solid Phase Extraction (SPE)</strong></p><p>A strong cation-exchange functionalized polymeric sorbent that allows for complete retention of basic compounds with a <strong>pKa less than 10.5,</strong> making <strong>100% organic wash conditions possible</strong>. A 100% organic wash ensures that the maximum amount of interferences are removed from the target compound.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_C_SPE_4927d7340d.jpg" alt="Phenomenex: Strata-X-C SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_C_SPE_4927d7340d.jpg 245w," sizes="100vw" width="500" height="268"></p><ul><li><strong>Recommended Use: </strong>Extraction of weakly basic compounds</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>For Bases with pKa ≤ 10.5</strong></h5><ul><li><strong>Column: </strong>1 mL Methanol</li><li><strong>Equilibrate: </strong>1 mL Acidified Water</li><li><strong>Load: </strong>Diluted Acidified Sample</li><li><strong>Wash 1: </strong>1 mL 0.1 N HCI in Water (collect this fraction to analyze Polar Neutrals)</li><li><strong>Wash 2: </strong>1 mL 0.1 N HCI in Methanol (collect this fraction to analyze Neutrals/Acids)</li><li><strong>Elute Bases: </strong>2x 500 µL 5 % NH4OH in Methanol</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_single_tube_435d45d0ad.jpg" alt="Phenomenex: Strata X single tube" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_single_tube_435d45d0ad.jpg 156w," sizes="100vw" width="1080" height="1080"></p><p><i>Based on 30 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</i></p><h4><strong>Available Formats</strong></h4><ul><li><strong>96-Well-Plate</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_96_well_plate_9a66005814.jpg" alt="Phenomenex: Strata X 96-well plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_96_well_plate_9a66005814.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>1, 3, and 6mL Tubes</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg" alt="Phenomenex: Strata X 1, 3, and 6mL Tubes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>Giga Tubes (12-150mL Tubes)</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg" alt="Phenomenex: Strata X Giga Tubes (12-150mL Tubes)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg 156w," sizes="100vw" width="1080" height="1080"></p>

Phenomenex Strata X-CW Solid Phase Extraction (SPE)

Strata-X-CW weak cation-exchange SPE retains strong bases (pKa >8) with 100% organic wash for maximum cleanup. Available in tubes, 96-well plates, and giga formats.

<p><strong>Weak Cation Mixed-Mode Solid Phase Extraction (SPE)</strong></p><p>A weak cation-exchange functionalized polymeric sorbent that allows for complete retention of basic compounds with a <strong>pKa greater than 8</strong>, making <strong>100% organic wash conditions possible</strong>. A 100% organic wash ensures that the maximum amount of interferences are removed from the target compound.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_CW_SPE_b16a0e0baf.jpg" alt="Phenomenex: Strata-X-CW SPE" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_CW_SPE_b16a0e0baf.jpg 245w," sizes="100vw" width="500" height="268"></p><ul><li><strong>Recommended Use: </strong>Extraction of basic compounds, particularly strong bases</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>For Bases with pKa &gt; 8</strong></h5><ul><li><strong>Column: </strong>1 mL Methanol</li><li><strong>Equilibrate: </strong>1 mL Water, pH 6-7</li><li><strong>Load: </strong>Diluted Sample, pH 6-7</li><li><strong>Wash 1: </strong>1 mL Water, pH 6-7</li><li><strong>Wash 2: </strong>1 mL Methanol (collect this fraction to analyze Neutrals/Acids)</li><li><strong>Elute Any Bases: </strong>2x 500 µL 5 % Formic Acid in Methanol</li><li><strong>Elute Weak Bases: </strong>2x 500 µL 5 % NH4OH in Methanol</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_single_tube_435d45d0ad.jpg" alt="Phenomenex: Strata X single tube" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_single_tube_435d45d0ad.jpg 156w," sizes="100vw" width="1080" height="1080"></p><p><i>Based on 30 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</i></p><h4><strong>Available Formats</strong></h4><ul><li><strong>96-Well-Plate</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_96_well_plate_9a66005814.jpg" alt="Phenomenex: Strata X 96-well plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_96_well_plate_9a66005814.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>1, 3, and 6mL Tubes</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg" alt="Phenomenex: Strata X 1, 3, and 6mL Tubes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>Giga Tubes (12-150mL Tubes)</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg" alt="Phenomenex: Strata X Giga Tubes (12-150mL Tubes)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg 156w," sizes="100vw" width="1080" height="1080"></p>

Phenomenex Strata X Solid Phase Extraction (SPE)

Strata-X reversed phase SPE retains neutrals, acids, and bases via π-π, hydrogen bonding, and hydrophobic interactions. Robust cleanup under high organic wash.

<p><strong>Reversed Phase Solid Phase Extraction (SPE)</strong></p><p>A reversed phase functionalized polymeric sorbent that gives strong retention of neutral, acidic, or basic compounds under aggressive, high organic wash conditions. This sorbent relies on <strong>3 mechanisms of retention</strong>: <strong>pi-pi bonding</strong>, <strong>hydrogen bonding</strong> (dipole-dipole interactions), and <strong>hydrophobic interaction</strong>.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_d8f4451e42.jpg" alt="Phenomenex: Strata-X" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_d8f4451e42.jpg 245w," sizes="100vw" width="433" height="247"></p><ul><li><strong>Recommended Use: </strong>Extraction of neutrals and aromatics</li></ul><h4><strong>Starting Method</strong></h4><h5><strong>For Neutral Compounds</strong></h5><ul><li><strong>Column: </strong>1 mL Methanol</li><li><strong>Equilibrate: </strong>1 mL Water</li><li><strong>Load: </strong>Diluted Sample</li><li><strong>Wash: </strong>1 mL 5-60 % Methanol</li><li><strong>Elute:</strong> 2x 500 µL 2 % Formic Acid in Methanol/Acetonitrile</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_single_tube_435d45d0ad.jpg" alt="Phenomenex: Strata X single tube" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_single_tube_435d45d0ad.jpg 156w," sizes="100vw" width="1080" height="1080"></p><p><i>Based on 30 mg/1 mL sorbent mass. The above is a convenient starting point for SPE method development, further optimization may be required to tailor the method for your specific extraction needs.</i></p><h4><strong>Available Formats</strong></h4><ul><li><strong>96-Well-Plate</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_96_well_plate_9a66005814.jpg" alt="Phenomenex: Strata X 96-well plate" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_96_well_plate_9a66005814.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>1, 3, and 6mL Tubes</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg" alt="Phenomenex: Strata X 1, 3, and 6mL Tubes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_1_9b04cab6c1.jpg 156w," sizes="100vw" width="1080" height="1080"></p><ul><li><strong>Giga Tubes (12-150mL Tubes)</strong></li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg" alt="Phenomenex: Strata X Giga Tubes (12-150mL Tubes)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Strata_X_tubes_2_a8cd1706ec.jpg 156w," sizes="100vw" width="1080" height="1080"></p>

Phenomenex Biozen N-Glycan Clean-Up

Biozen N-Glycan Clean-up enables fast, efficient SPE purification of labeled, released N-glycans using HILIC microelution, ideal for small sample volumes and LC-MS workflows.

<h4><strong>Easy Clean-up of Labeled, Released N-Glycans Using Solid Phase Extraction (SPE)</strong></h4><p>SPE HILIC stationary phase that excels at retention and recovery labeled released N-glycans. Microelution format allows for streamlined processing and clean-up of small sample volumes.</p><ul><li>Small volume format allows for more concentrated samples</li><li>Minimal elution solvent</li><li>Excellent retention and recovery of labeled, released N-glycans</li><li>Faster clean-up methods to save on sample prep time</li></ul><h4><strong>Protocol</strong></h4><ul><li><strong>96-Well Plate: </strong>Biozen N-Glycan Clean-up</li><li><strong>Part No.: </strong>8M-S009-NGA</li><li><strong>Condition: </strong>200 µL Water</li><li><strong>Equilibrate:</strong> 200 µL Water/Acetonitrile (15:85)</li><li><strong>Load:</strong> Labeled Sample (up to 400 µL of labeled sample)</li><li><strong>Wash: </strong>2x 600 µL Formic acid/Water/Acetonitrile (1:9:90)</li><li><strong>Elute: </strong>3x 30 µL 200 mM Ammonium acetate in Acetonitrile/Water (5:95) of labeled sample)</li><li><strong>Dilute:</strong> 100 µL Dimethylformamide and then 210 µL of Acetonitrile</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Biozen_N_Glycan_962a23eee6.jpg" alt="Phenomenex: Biozen N-Glycan Clean-up" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Biozen_N_Glycan_962a23eee6.jpg 245w," sizes="100vw" width="1444" height="424"></p>

Phenomenex Clarity OTX Clean-Up

Rapid 15-minute clean-up of biological samples using Clarity OTX SPE enables efficient isolation of RNA- and DNA-based therapeutics without LLE, optimized for LC-MS bioanalysis.

<h4><strong>15 Minute Clean Up from Biological Samples</strong></h4><p><strong>Isolate RNA and DNA-based therapeutics / metabolites from biological fluids and tissues in less time with Clarity OTX solid phase extraction (SPE) and buffer products.</strong></p><ul><li>No liquid-liquid extraction (LLE) required required</li><li>&gt;80 % typical extraction recoveries</li><li>Optimized for LC-MS bioanalysis</li></ul><h3><app-cb-header style="color:rgb(65, 66, 69);font-family:proxima-nova, sans-serif;font-size:16px;font-style:normal;font-weight:400;letter-spacing:normal;text-align:left;text-indent:0px;text-transform:none;"><div><div><h2 style="border-bottom:1px solid rgb(51, 51, 51);color:rgb(0, 41, 72);font-size:32px;font-style:normal;font-weight:400;line-height:1.2;"><div>General Extraction</div></h2></div></div></app-cb-header><app-cb-fourtext-eightimage style="color:rgb(65, 66, 69);font-family:proxima-nova, sans-serif;font-size:16px;font-style:normal;font-weight:400;letter-spacing:normal;text-align:left;text-indent:0px;text-transform:none;"><div><div><div style="flex-wrap:wrap;"><div style="flex:0 0 100%;"><h2 style="color:rgb(0, 41, 72);font-size:32px;font-weight:400;line-height:1.2;">Common Extraction Procedure (~180 minutes)</h2></div></div></div></div></app-cb-fourtext-eightimage><strong>General Extraction</strong></h3><h4><strong>Common Extraction Procedure (~180 minutes)</strong></h4><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Clarity_OTX_Clean_Up_e317411382.jpg" alt="Phenomenex: Clarity OTX Clean-Up: Common Extraction Procedure (~180 minutes)" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Clarity_OTX_Clean_Up_e317411382.jpg 245w," sizes="100vw" width="678" height="374"></p><h5><strong>Suitable for Most Oligo Therapeutics &amp; Samples</strong></h5><p><strong>Oligo types / Sample Types</strong></p><ul><li>DNA: Plasma</li><li>Aptamers: Serum</li><li>RNAi/siRNA: Urine</li><li>Thioates: Tears</li><li>Lipid-conjugates: Saliva</li><li>Liposome encapsulated: Tissue</li></ul><h4><strong>Extraction Protocol</strong></h4><p><strong>Sample Pre-Treatment</strong></p><ul><li><strong>Tissue:</strong><ul><li>Proteinase K digestion or homogenize</li><li>Mix 1-to-1 with Lysis-Loading buffer</li></ul></li><li><strong>Biological Fluids: </strong>Mix 1-to-1 with Lysis-Loading buffer</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Phenomenex_Clarity_OTX_Clean_Up_2_fd322c63cd.jpg" alt="Phenomenex: Clarity OTX Clean-Up: Extraction Protocol" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Phenomenex_Clarity_OTX_Clean_Up_2_fd322c63cd.jpg 245w," sizes="100vw" width="1031" height="494"></p>

Thermo Scientific QuEChERS Sample Preparation Kits

QuEChERS is a versatile sample preparation method for analyzing pesticides, veterinary drugs, and other residues in various sample types before GC-MS or LC-MS analysis.

<div><div><div><h3><strong>QuEChERS sample preparation—now easier, more convenient, and affordable</strong></h3><p><strong>QuEChERS</strong> (<strong><u>Q</u></strong><u>u</u>ick, <strong><u>E</u></strong>asy, <strong><u>C</u></strong>heap, <strong><u>E</u></strong>ffective, <strong><u>R</u></strong>ugged, and <strong><u>S</u></strong>afe)is a <strong>sample preparation method</strong> that was initially developed in 2003 for <strong>analyzing veterinary drugs in food</strong>. The method was also tested for <strong>pesticide residue analysis in plant material</strong> with great success. In 2003, the <strong>detailed method was published</strong> in the journal AOAC International. Since then, the QuEChERS method has evolved into a <strong>sample preparation technique used on a variety of analytes</strong> in an <strong>expanding number of sample types</strong> before analysis by <a target="_blank" rel="noopener noreferrer" href="https://www.thermofisher.com/cz/en/home/industrial/mass-spectrometry/gas-chromatography-mass-spectrometry-gc-ms.html"><strong>GC-MS</strong></a><strong> or </strong><a target="_blank" rel="noopener noreferrer" href="https://www.thermofisher.com/cz/en/home/industrial/mass-spectrometry/liquid-chromatography-mass-spectrometry-lc-ms.html"><strong>LC-MS</strong></a>.</p><p><strong>Thermo Scientific QuEChERS kits</strong> contain <strong>pre-packaged, ready-weighed salts, sorbents, and buffers</strong> to <strong>streamline your workflow</strong> and <strong>minimize the potential for error</strong>. The kits are grouped according to your <strong>analytes of interest</strong>, <strong>sample matrix</strong>, and <strong>preferred QuEChERS method</strong>:</p><ul><li><strong>Original 2003 Method</strong></li><li><strong>AOAC 2007.01 Method</strong></li><li><strong>EN 15662 Method</strong></li><li><strong>NY/T 1380-2007 Method</strong></li></ul><p><strong>Complete packages</strong>—including both <strong>extraction and clean-up kits</strong>—are available. <strong>Extraction-only and cleanup-only kits</strong> are also offered to suit your laboratory’s sample preparation needs. These <strong>pre-packaged kits save time and money</strong>, make QuEChERS procedures <strong>easier and more convenient</strong>, and ensure <strong>quality to yield reproducible results</strong> and <strong>excellent recoveries</strong> for a wide variety of analytes.</p><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_2_1e99f0c81b.jpg" alt="Thermo Scientific QuEChERS Sample Preparation Kits" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_2_1e99f0c81b.jpg 217w," sizes="100vw" width="891" height="640"></p><h3><strong>Typical QuEChERS workflow</strong></h3><div><div><div><div><div><p>As shown in the workflow diagram below, the <strong>QuEChERS method has four basic steps</strong>:</p><ol><li><strong>Homogenize sample</strong> (fruit or vegetable)</li><li><strong>Extract analytes of interest</strong> from a sample using <strong>extraction salts</strong> (pesticide residues, veterinary drugs, and/or mycotoxins)</li><li><strong>Clean-up the resulting supernatant</strong> using <strong>dispersive solid phase extraction (dSPE)</strong></li><li><strong>Analyze by GC-MS or LC-MS</strong></li></ol><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_496491ceff.jpeg" alt="Thermo Scientific QuEChERS Sample Preparation Kits" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_496491ceff.jpeg 245w," sizes="100vw" width="1170" height="706"></p><div><h3><strong>QuEChERS products</strong></h3></div><div><h4><strong>QuEChERS extraction kits for original 2003 method</strong></h4></div><div><p>The <strong>original QuEChERS method</strong> (Anastassiades et al, 2003) was developed by <strong>Steven J. Lehotay and Michelangelo Anastassiades</strong> in 2003 for the <strong>determination of pesticide residues in fruits and vegetables</strong>. The original method was created to <strong>analyze non-base-sensitive compounds</strong> and uses a <strong>sodium chloride buffer</strong> to <strong>reduce polar interferences</strong> and <strong>enhance extraction</strong>. <strong>Buffering</strong> is an important part of the QuEChERS procedure because it <strong>allows for analysis of pesticides and other residues</strong> that display <strong>pH dependence in their recoveries</strong>, depending on the <strong>sample matrix</strong>. <strong>Three different extraction kits</strong> are available to support the <strong>original 2003 QuEChERS method</strong>.</p><h5><strong>Chemicals used in the original 2003 method</strong></h5></div><ul><li><strong>Acetonitrile:</strong> Used to perform single-phase extraction (SPE) on a sample</li><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>NaCl:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes residual water from sample; reduces polar interference and enhances extraction</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dispersive solid phase extraction (dSPE) step</li></ul><div><h4><strong>QuEChERS extraction and clean-up kits for AOAC 2007.01 method</strong></h4><p>The <strong>AOAC 2007.01 QuEChERS Method</strong> was developed by <strong>Steven J. Lehotay and his co-workers</strong>, who <strong>modified the original 2003 method</strong> to accommodate the use of <strong>acetate buffering at higher concentration</strong> for <strong>greater buffering strength</strong>. <strong>Buffering</strong> is an important part of the QuEChERS procedure because it <strong>allows for analysis of pesticides and other residues</strong> that display <strong>pH dependence in their recoveries</strong>, depending on the <strong>sample matrix</strong>. These <strong>extraction and clean-up products</strong> here support the <strong>AOAC 2007.01 method</strong>.</p><div><h5><strong>Chemicals used in the AOAC 2007.01 method</strong></h5><ul><li><strong>Acetonitrile:</strong> Used to perform single-phase extraction on a sample</li><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>NaOAc:</strong> Buffers the sample to stabilize pH</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>C18:</strong> Removes fats, sterols, and other non-polar interferences from sample</li><li><strong>GCB:</strong> Graphitized carbon black, removes pigment (<i>not recommended for use with planar pesticides</i>)</li></ul><div><h4><strong>QuEChERS extraction and clean-up kits for EN 15662 method</strong></h4><p>The <strong>extraction and clean-up products</strong> here support the <strong>EN 15662 method</strong>. <strong>Widely used in Europe</strong>, the EN 15662 method was developed by <strong>Michelangelo Anastassiades and co-workers</strong>, who <strong>modified the original 2003 method</strong> to accommodate the use of <strong>citrate buffering at a relatively low buffering capacity</strong>. This variation uses a <strong>sodium chloride buffer</strong> to <strong>minimize polar interferences</strong> in addition to <strong>sodium citrate dihydrate</strong> and <strong>disodium citrate sesquihydrate buffers</strong>. <strong>Buffering</strong> is an important part of the QuEChERS procedure because it <strong>allows for analysis of pesticides and other residues</strong> that display <strong>pH dependence in their recoveries</strong>, depending on the <strong>sample matrix</strong>.</p><h5><strong>Chemicals used in the EN 15662 method</strong></h5><ul><li><strong>Acetonitrile:</strong> Used to perform single-phase extraction on a sample</li><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>NaCl:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes residual water from sample</li><li><strong>Trisodium Citrate:</strong> Buffers the sample to stabilize pH</li><li><strong>Disodium Citrate Sesquihydrate:</strong> Buffers the sample to stabilize pH</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>C18:</strong> Removes fats, sterols, and other non-polar interferences from sample</li><li><strong>GCB:</strong> Graphitized carbon black, removes pigment (<i>not recommended for use with planar pesticides</i>)</li></ul><p><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_3_721562526f.jpg" alt="Thermo Scientific QuEChERS Sample Preparation Kits" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_Thermo_Scientific_Qu_E_Ch_ERS_Sample_Preparation_Kits_3_721562526f.jpg 245w," sizes="100vw" width="1471" height="488"></p><div><h4><strong>QuEChERS clean-up kit for NY/T 1380-2007 method</strong></h4></div><div><p>The <strong>NY/T 1380-2007 method</strong> is <strong>recommended by China Ministry of Agriculture</strong> for the <strong>QuEChERS Method sample preparation</strong> of <strong>51 specific pesticide residues</strong> in <strong>fruits and vegetables</strong> with <strong>analysis by GC-MS</strong>.</p><h5><strong>Chemicals used in the NY/T 1380-2007 method</strong></h5><ul><li><strong>Anhydrous MgSO₄:</strong> Induces phase separation between water content in sample and acetonitrile layer during liquid-liquid partitioning step; removes remaining water from sample during dispersive solid phase extraction (dSPE) step</li><li><strong>PSA:</strong> Primary secondary amine, used to remove polar matrix components, citric co-extractives, and free fatty acids, from sample during dSPE step</li><li><strong>C18:</strong> Removes fats, sterols, and other non-polar interferences from sample</li></ul></div></div></div></div></div></div></div></div></div></div></div></div>

Products from category Consumables - page 1

Related content

Exploring sequence space beyond random mutagenesis

News from LabRulezLCMS Library - Week 04, 2026

Why are my recoveries greater than 100%?