Solid Phase Extraction (SPE) is one of the most highly selective sample preparation methods, meaning that the targeted analytes and their matrices must be considered when choosing the correct SPE sorbent and format. Drying down the sorbent before elution is an important step.<ul><li>Wash solvents are used to flush out unwanted compounds (i.e., contaminants). If the wash solvent is not completely removed, then residual wash solvent could contaminate the final elution.</li><li>If you do not dry the SPE sufficiently, it could make the final solution less concentrated and result in a reduction in sensitivity.</li><li>Drying helps physically break down the interactions between the sorbent and analyte for a more concentrated extract.</li></ul>After the wash solvent has been passed through the cartridge, continue to apply negative pressure (vacuum) or positive pressure. Use this pressure to dry the cartridge for 2 to 5 minutes (or until dry). Turn off the pressure and wipe the tips of the manifold needles to remove any residual solvent.<h5>Notes</h5><ol><li>Reproducibility: Drying removes traces of residual sample/matrix and wash solvent from the sorbent. This produces a more concentrated final extract with a consistent volume and composition and yields better reproducibility and higher recoveries.</li><li>Immiscibility: Drying is especially critical when using elution solvents that are immiscible with water (e.g. hexane, ethyl acetate, and methylene chloride). Residual water in the sorbent bed may prevent dissolution of the analyte in the elution solvent, resulting in low recoveries and irreproducibility.</li><li>Over-drying: Avoid over-drying the sorbent, since in some cases, analyte recovery may decrease with excessive vacuum or drying times above 5 minutes. Dry cartridges look distinctly different from moist ones. Make a note of the cartridge appearance before and after conditioning. Also, you could touch the cartridge while it is drying; wet cartridges feel colder than dry cartridges.&nbsp;</li></ol>

Why Is It Necessary to Dry the SPE Sorbent Before Elution?

<h3>Mastering Ion-Pair Reversed-Phase Chromatography for Oligonucleotide Analysis</h3><h4>Why Purity Is Critical in the Oligonucleotide Era</h4>Oligonucleotides — short, synthetic strands of DNA or RNA — are central to modern biotechnology. They power gene therapies, advanced diagnostics, and cutting-edge molecular research. However, before these molecules can be used in clinical or research settings, their purity and structural integrity must be thoroughly verified. High-resolution chromatographic analysis plays a crucial role in ensuring quality and safety.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Figure_1_Separation_Example_of_Oligonucleotides_5577514561.jpg" alt="KNAUER: Figure 1 - Separation Example of Oligonucleotides." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Figure_1_Separation_Example_of_Oligonucleotides_5577514561.jpg 245w," sizes="100vw" width="1024" height="368"><h4>Understanding Ion-Pair Reversed-Phase (IP-RP) Chromatography</h4>For scientists involved in oligonucleotide synthesis and characterization, Ion-Pair Reversed-Phase Chromatography (IP-RP) is one of the most effective analytical tools available.Unlike separation techniques that rely solely on charge differences, IP-RP combines:<ul><li>Ionic interactions</li><li>Hydrophobic interactions</li></ul>This dual retention mechanism enables exceptional resolution — even for oligonucleotides that differ by only a single nucleotide or subtle chemical modification. Whether assessing synthesis efficiency or purifying therapeutic-grade material, IP-RP provides reliable, reproducible separations.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Figure_2_Overview_of_IP_RP_Mode_prinicple_ecd54b6e9c.jpg" alt="KNAUER: Figure 2 - Overview of IP-RP Mode prinicple." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Figure_2_Overview_of_IP_RP_Mode_prinicple_ecd54b6e9c.jpg 245w," sizes="100vw" width="1024" height="456"><h4>The Principle Behind Ion-Pairing</h4>Oligonucleotides possess a highly negatively charged phosphate backbone. In a traditional reversed-phase system, such hydrophilic, charged molecules would show little retention.IP-RP overcomes this limitation by introducing a positively charged ion-pairing reagent into the mobile phase. The cation associates with the negatively charged oligonucleotide, forming a transient ion pair with increased hydrophobic character. This modified complex can now interact with the hydrophobic stationary phase.Retention strength depends on:<ul><li>The hydrophobicity of the ion-pair reagent</li><li>The strength of ionic interaction</li><li>The applied organic gradient</li></ul>During gradient elution (commonly using acetonitrile), analytes are released in a controlled manner according to size, sequence, and chemical modifications.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Figure_3_Ion_Pair_Reversed_Phase_Principle_9a4fcd12f2.jpg" alt="KNAUER: Figure 3 - Ion-Pair Reversed Phase Principle." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Figure_3_Ion_Pair_Reversed_Phase_Principle_9a4fcd12f2.jpg 245w," sizes="100vw" width="1024" height="393"><h4>Choosing the Right Ion-Pair Reagent</h4>Successful IP-RP separation depends heavily on selecting an appropriate ion-pair reagent. Two key factors determine retention behavior:<ol><li>Alkyl chain length</li><li>Charge density</li></ol><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Figure_4_Ion_Pair_Classification_eaad172a4e.jpg" alt="KNAUER: Figure 4 - Ion-Pair Classification." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Figure_4_Ion_Pair_Classification_eaad172a4e.jpg 245w," sizes="100vw" width="1024" height="398"><h4>Strong Cationic Ion-Pair Reagents</h4>Ion-pair reagents with longer alkyl chains provide stronger hydrophobic interactions and increased retention. A widely used example is tetrabutylammonium (TBA⁺), frequently applied for strongly retained anionic analytes.These reagents are particularly useful when high retention strength is required.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Table_1_Strong_Cationic_Ion_Pair_Reagents_8dbf00c57e.jpg" alt="KNAUER: Table 1 - Strong Cationic Ion-Pair Reagents." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Table_1_Strong_Cationic_Ion_Pair_Reagents_8dbf00c57e.jpg 245w," sizes="100vw" width="1024" height="396"><h4>Volatile (Weaker) Ion-Pair Reagents</h4>Short-chain ion-pair reagents generate weaker retention but offer a significant advantage: compatibility with LC–MS detection.Triethylammonium (TEA⁺) is among the most commonly used reagents for oligonucleotide analysis, particularly when mass spectrometric detection is involved. Other options, such as diisopropylethylammonium (DIEA⁺), are also widely applied, often combined with HFIP to enhance MS performance.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Table_2_Weak_Cationic_Ion_Pair_Reagents_6332a4975e.jpg" alt="KNAUER: Table 2 - Weak Cationic Ion-Pair Reagents." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Table_2_Weak_Cationic_Ion_Pair_Reagents_6332a4975e.jpg 245w," sizes="100vw" width="1024" height="283"><h4>Building an IP-RP Method for Oligonucleotides</h4>Developing a robust IP-RP method follows a logical sequence:<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Table_3_IP_RP_Method_Step_Procedure_for_Oligos_c2216c24a0.jpg" alt="KNAUER: Table 3 - IP-RP Method Step Procedure for Oligos." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Table_3_IP_RP_Method_Step_Procedure_for_Oligos_c2216c24a0.jpg 245w," sizes="100vw" width="1024" height="304"><h5>1. Characterize the Analyte</h5>Oligonucleotides typically contain 10–50+ nucleotides and exhibit high negative charge density. This necessitates a suitable cationic partner such as TEA⁺ or DIEA⁺.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Figure_5_Cationic_Ion_Pair_Principle_for_Oligonucleotides_cb2dfb7457.jpg" alt="KNAUER: Figure 5 - Cationic Ion-Pair Principle for Oligonucleotides." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Figure_5_Cationic_Ion_Pair_Principle_for_Oligonucleotides_cb2dfb7457.jpg 245w," sizes="100vw" width="512" height="320"><h5>2. Select the Column</h5>Use a reversed-phase column with:<ul><li>Large pore size (≈300 Å)</li><li>Appropriate internal diameter</li></ul>These parameters support the so-called “ON–OFF” retention mechanism — a bind-and-elute behavior where analytes are strongly retained until the gradient triggers rapid elution.<h5>3. Optimize the Mobile Phase</h5>A typical starting condition includes:<ul><li>10 mM TEA buffer at pH ~7</li><li>Acetonitrile as organic modifier</li></ul>Gradient programs from approximately 5% to 50% organic solvent over 15–30 minutes are commonly effective for complex oligonucleotide mixtures.<h5>4. Adjust Retention Strength if Needed</h5>To increase retention:<ul><li>Raise ion-pair concentration (up to ~100 mM if required)</li><li>Select a more hydrophobic ion-pair reagent</li></ul><h5>5. Validate the Method</h5>Ensure robustness, sensitivity, and reproducibility by carefully evaluating:<ul><li>UV chromatograms</li><li>MS traces</li><li>Peak shape and resolution</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Figure_6_UV_MS_traces_of_IP_RP_Oligonucleotide_Analysis_81faf4e9f0.jpg" alt="KNAUER: Figure 6 - UV-MS traces of IP-RP Oligonucleotide Analysis." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Figure_6_UV_MS_traces_of_IP_RP_Oligonucleotide_Analysis_81faf4e9f0.jpg 245w," sizes="100vw" width="1024" height="365"><h4>Why IP-RP Is Considered the Gold Standard</h4>Ion-Pair Reversed-Phase Chromatography uniquely combines the resolving power of reversed-phase LC with the ability to retain highly polar, charged biomolecules.Its advantages include:<ul><li>Tunable selectivity</li><li>Compatibility with UV and MS detection</li><li>Scalability from analytical to preparative workflows</li><li>Applicability from research to pharmaceutical production</li></ul>By transforming highly charged oligonucleotides into hydrophobic ion-pair complexes, IP-RP enables precise and reproducible separations that would otherwise be impossible in conventional reversed-phase systems.For these reasons, IP-RP is widely regarded as the benchmark technique for oligonucleotide analysis.<h4>Final Thoughts</h4>Mastering IP-RP is less intimidating than it may seem. A successful method comes down to:<ul><li>Selecting the right ion-pair reagent</li><li>Choosing a suitable column</li><li>Optimizing gradient conditions</li><li>Fine-tuning temperature and concentration parameters</li></ul>With thoughtful method development, IP-RP delivers sharp peaks, clean separations, and reliable performance — fully compatible with modern mass spectrometry workflows and ready to meet the demands of advanced oligonucleotide analysis.

Oligos Made Easy - Part 3: IP-RP

News from LabRulezLCMS Library - Week 08, 2026

Article

Application

Academy

Video

Presentation

Science and research

Everything from the world of analytical chemistry in one place. We connect people in solving their problems. At Labrulez you will find all the necessary information easily, quickly and clearly. Stop searching and start finding.

LabRulez

Phenomenex is a global technology leader committed to developing novel analytical chemistry solutions that solve the separation and purification challenges of researchers in industrial, government and academic laboratories.

Phenomenex

Based in Berlin, KNAUER is a medium-sized, owner-managed company that has been serving the sciences since 1962. We develop and manufacture scientific instruments of superior quality for liquid chromatography, including: Analytical HPLC/UHPLC, Preparative HPLC, Fast protein liquid chromatography (FPLC), Multi-column chromatography/Simulated moving bed (SMB) chromatography. High pressure dosing, in-line detection systems, and osmometry are additional business areas.

KNAUER

KNAUER Eurosil Bioselect 300 C8 HPLC Columns (USP L7)

Eurosil Bioselect C8 has been specifically developed for the determination and purification of peptides, proteins, and oligonucleotides up to a molecular weight of approximately 20 kDa.

Analytical wide pore phase for the determination of biomolecules bigger than 5000 DaEurosil Bioselect C8 has been specifically developed for the determination and purification of peptides, proteins, and oligonucleotides up to a molecular weight of approximately 20 kDa.<h5>Properties</h5><ul><li>Ultra pure, spherical wide pore HPLC phase based on wide pore silica gel</li><li>Unpolar, monomeric C8 modification, endcapped</li><li>4.5 % carbon content (conventional endcapping)</li><li>Separation mechanism: hydrophobic interaction</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_C8_hydrosphob_6986c292b4.webp" alt="KNAUER: C8" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_C8_hydrosphob_6986c292b4.webp 144w," sizes="100vw" width="381" height="413"><h5>Recommended application areas</h5><ul><li>Hydrophilic biomolecules, peptides, peptide mapping after enzymatic digestion</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_Phases_98acc32d0e.jpg" alt="KNAUER: Eurosil Bioselect - Phases and recommended sizes of molecules" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_Phases_98acc32d0e.jpg 245w," sizes="100vw" width="1385" height="778"><h3>KNAUER Wide pore HPLC columns</h3>For enhanced resolution, capacity and recovery of proteins and other biomolecules<ul><li>Material: Silica or polymer particles</li><li>Separation Ranges: 2–100 kDa</li><li>Column Brands: Eurosil Bioselect or AppliChrom®</li><li>Particle sizes: 3–10 µm</li><li>Pore Sizes: 300 or 100–1000 Å</li><li>Specific surface: 90 ± 5 m2/g</li><li>Pore volume: 0.8 ml/g</li><li>Density: 450 g/l</li><li>Applications: Peptides exceeding approximately 50 amino acids and oligonucleotides greater than 25 residues</li><li>Customize: Bioanalysis requires a lot of flexibility in the pore size, the pH range, the temperatures and the solvents used. To achieve this, we cross phase limits.</li></ul><h4>Characteristics&nbsp;</h4><ul><li>Eurosil Bioselect columns are available in 4 modifications, useful for a wide range of separation tasks involving large molecules up to 100 000 Da.</li><li>Strict manufacturing procedures ensure a very narrow pore size distribution.</li><li>Interfering anions or heavy metal ions on the silica surface are not present in Eurosil Bioselect columns because only ultra pure silica gel and high quality chemical modifications are employed.</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_85cfc2d201.jpg" alt="KNAUER: Eurosil Bioselect" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_85cfc2d201.jpg 222w," sizes="100vw" width="1114" height="782"><h4>Separation mechanism of Eurosil Bioselect</h4>To separate larger molecules, they need to freely access the interior of the pores of the packing material. Therefore, the analytes’ diameter must be smaller than the average pore diameter.&nbsp;For higher molecular weight solutes, the use of lower pore size materials (60-120 Å) as typically used for the analysis of small molecules may result restricted diffusion in the material´s pores and therewith reduced column efficiency.&nbsp;<h4>Modifications</h4>The recommended modification of Eurosil Bioselect depends on the molecular weight of the analytes.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_chemical_modifications_1fd5d87f7b.jpg" alt="KNAUER: Eurosil Bioselect - chemical modifications" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_chemical_modifications_1fd5d87f7b.jpg 245w," sizes="100vw" width="955" height="505"> &nbsp;

KNAUER Eurosil Bioselect 300 C18 HPLC Columns (USP L1)

Eurosil Bioselect C18 has been specifically developed for the determination and purification of peptides, proteins, and oligonucleotides up to a molecular weigth of approximately 5 kDa.

Analytical wide pore phase for the determination of biomolecules bigger than 2000 Da​Eurosil Bioselect C18 has been specifically developed for the determination and purification of peptides, proteins, and oligonucleotides up to a molecular weigth of approximately 5 kDa.<h5>Properties</h5><ul><li>Ultra pure, spherical wide pore HPLC phase based on silica gel</li><li>Unpolar, monomeric C18 (Octadecyl) modification, endcapped</li><li>7.5 % carbon content (conventional endcapping)</li><li>Separation mechanism: hydrophobic interaction</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_C18_Endcapped_standard_edd2523aca.webp" alt="KNAUER: C18 Endcapped standard" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_C18_Endcapped_standard_edd2523aca.webp 234w," sizes="100vw" width="688" height="458"><h5>Recommended application areas</h5><ul><li>Hydrophilic biomolecules, peptides, peptide mapping after enzymatic digestion</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_Phases_98acc32d0e.jpg" alt="KNAUER: Eurosil Bioselect - Phases and recommended sizes of molecules" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_Phases_98acc32d0e.jpg 245w," sizes="100vw" width="1385" height="778"><blockquote>Tip: Caused by the larger pore size of 300 Å, Eurosil Bioselect phases are not as mechanical stable as classical silica gel phases with up to 150 Å and should not be used above 200 bar pressure.</blockquote><h3>KNAUER Wide pore HPLC columns</h3>For enhanced resolution, capacity and recovery of proteins and other biomolecules<ul><li>Material: Silica or polymer particles</li><li>Separation Ranges: 2–100 kDa</li><li>Column Brands: Eurosil Bioselect or AppliChrom®</li><li>Particle sizes: 3–10 µm</li><li>Pore Sizes: 300 or 100–1000 Å</li><li>Specific surface: 90 ± 5 m2/g</li><li>Pore volume: 0.8 ml/g</li><li>Density: 450 g/l</li><li>Applications: Peptides exceeding approximately 50 amino acids and oligonucleotides greater than 25 residues</li><li>Customize: Bioanalysis requires a lot of flexibility in the pore size, the pH range, the temperatures and the solvents used. To achieve this, we cross phase limits.</li></ul><h4>Characteristics&nbsp;</h4><ul><li>Eurosil Bioselect columns are available in 4 modifications, useful for a wide range of separation tasks involving large molecules up to 100 000 Da.</li><li>Strict manufacturing procedures ensure a very narrow pore size distribution.</li><li>Interfering anions or heavy metal ions on the silica surface are not present in Eurosil Bioselect columns because only ultra pure silica gel and high quality chemical modifications are employed.</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_85cfc2d201.jpg" alt="KNAUER: Eurosil Bioselect" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_85cfc2d201.jpg 222w," sizes="100vw" width="1114" height="782"><h4>Separation mechanism of Eurosil Bioselect</h4>To separate larger molecules, they need to freely access the interior of the pores of the packing material. Therefore, the analytes’ diameter must be smaller than the average pore diameter.&nbsp;For higher molecular weight solutes, the use of lower pore size materials (60-120 Å) as typically used for the analysis of small molecules may result restricted diffusion in the material´s pores and therewith reduced column efficiency.&nbsp;<h4>Modifications</h4>The recommended modification of Eurosil Bioselect depends on the molecular weight of the analytes.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_chemical_modifications_1fd5d87f7b.jpg" alt="KNAUER: Eurosil Bioselect - chemical modifications" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_chemical_modifications_1fd5d87f7b.jpg 245w," sizes="100vw" width="955" height="505"> &nbsp;

KNAUER Eurosil Bioselect 300 C18A HPLC Columns (USP L1)

Eurosil Bioselect C18A has been specifically developed for the determination and purification of peptides, proteins, and oligonucleotides up to a molecular weigth of approximately 5 kDa.

Analytical wide pore phase for the determination of biomolecules up to 5000 Da​Eurosil Bioselect C18A has been specifically developed for the determination and purification of peptides, proteins, and oligonucleotides up to a molecular weigth of approximately 5 kDa.<h5>Properties</h5><ul><li>Ultra pure, spherical wide pore HPLC phase based on silica gel</li><li>Unpolar, monomeric C18 (Octadecyl) modification, endcapped</li><li>7 % carbon content (hydrophilic endcapping)</li><li>Separation mechanism: hydrophobic interaction</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_C18_A_6f4b0c3063.webp" alt="KNAUER: C18A" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_C18_A_6f4b0c3063.webp 245w," sizes="100vw" width="690" height="428"><h5>Recommended application areas</h5><ul><li>Hydrophilic and polar biomolecules, peptides, very polar biomolecules separated with 100 % aqueous eluents</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_Phases_98acc32d0e.jpg" alt="KNAUER: Eurosil Bioselect - Phases and recommended sizes of molecules" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_Phases_98acc32d0e.jpg 245w," sizes="100vw" width="1385" height="778"><h3>KNAUER Wide pore HPLC columns</h3>For enhanced resolution, capacity and recovery of proteins and other biomolecules<ul><li>Material: Silica or polymer particles</li><li>Separation Ranges: 2–100 kDa</li><li>Column Brands: Eurosil Bioselect or AppliChrom®</li><li>Particle sizes: 3–10 µm</li><li>Pore Sizes: 300 or 100–1000 Å</li><li>Specific surface: 90 ± 5 m2/g</li><li>Pore volume: 0.8 ml/g</li><li>Density: 450 g/l</li><li>Applications: Peptides exceeding approximately 50 amino acids and oligonucleotides greater than 25 residues</li><li>Customize: Bioanalysis requires a lot of flexibility in the pore size, the pH range, the temperatures and the solvents used. To achieve this, we cross phase limits.</li></ul><h4>Characteristics&nbsp;</h4><ul><li>Eurosil Bioselect columns are available in 4 modifications, useful for a wide range of separation tasks involving large molecules up to 100 000 Da.</li><li>Strict manufacturing procedures ensure a very narrow pore size distribution.</li><li>Interfering anions or heavy metal ions on the silica surface are not present in Eurosil Bioselect columns because only ultra pure silica gel and high quality chemical modifications are employed.</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_85cfc2d201.jpg" alt="KNAUER: Eurosil Bioselect" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_85cfc2d201.jpg 222w," sizes="100vw" width="1114" height="782"><h4>Separation mechanism of Eurosil Bioselect</h4>To separate larger molecules, they need to freely access the interior of the pores of the packing material. Therefore, the analytes’ diameter must be smaller than the average pore diameter.&nbsp;For higher molecular weight solutes, the use of lower pore size materials (60-120 Å) as typically used for the analysis of small molecules may result restricted diffusion in the material´s pores and therewith reduced column efficiency.&nbsp;<h4>Modifications</h4>The recommended modification of Eurosil Bioselect depends on the molecular weight of the analytes.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Eurosil_Bioselect_chemical_modifications_1fd5d87f7b.jpg" alt="KNAUER: Eurosil Bioselect - chemical modifications" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Eurosil_Bioselect_chemical_modifications_1fd5d87f7b.jpg 245w," sizes="100vw" width="955" height="505"> &nbsp;

KNAUER AppliChrom® ABOA SuperOH-P Columns for GPC/SEC

Optimally suited for aqueous SEC separations. Aqueous and highly hydrophilic polymeric base material.

AppliChrom® SEC columns for biopolymers and aqueous polymersOptimally suited for aqueous SEC separations. Aqueous and highly hydrophilic polymeric base material. Polymethacrylate resin, cross-linked with polyhydroxylated ether (surface contains some residual carboxyl functional groups)<h4>Properties:</h4><ul><li>Particle size: 7 µm for pore sizes up to 300 Å and 10 µm for pore sizes over 350 Å and the multipore columns</li><li>Stable between: pH 2–12.5</li><li>Pressure stable: for 30–70 bar depending on pore size</li><li>Temperature stability: between 10–85 °C</li><li>Flow rate: maximum 1 ml/min</li><li>Low column bleed for low detector noise</li><li>Large pore volume for optimal resolution</li><li>Individual pore sizes for individual molecular weight ranges</li><li>Multi-pore technology for a wide range of molecular sizes</li><li>Increased lifetime of SEC columns through combination of proprietary particle and packing technology</li><li>Recommended eluents: H₂O, buffers</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_Super_OH_P_Pore_sizes_4cb72c682d.jpg" alt="KNAUER: AppliChrom® ABOA SuperOH-P - Pore sizes" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_Super_OH_P_Pore_sizes_4cb72c682d.jpg 216w," sizes="100vw" width="1478" height="1071"><h4>Applications</h4>Water soluble (bio)polymers up to 40 000 kDa:<ul><li>proteins, oligonucleotides, virus, heparin, polyethylene oxide (PEO), polyethylene glycol (PEG), pullulan, maltodextrin, inulin, pectine, polycarboxylate ethers, gelatine, dextranes, polyacrylamide (PAM), PEGylated proteins acrylate dispersions</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

KNAUER AppliChrom® ABOA RPpetide GPC Columns for RP

AppliChrom® Polymer based reversed phase (RP) columns to reversed phase (RP) separation with orthogonal selectivity to silica based columns.

AppliChrom® Polymer based reversed phase (RP) columns<h4>Properties:</h4><ul><li>Rigid, spherical styrenedivinylbenzene copolymer&nbsp;</li><li>Particle sizes between: 3 to 30 μm</li><li>Pore sizes of: 100–1 000 Å</li><li>Reversed Phase (RP) separation with orthogonal selectivity to silica based columns</li><li>Improved chemical stability</li><li>Stable between: pH 1.5–14</li><li>Temperature stability: 10–90 °C</li><li>Stable towards pressures: up to 150 bar</li><li>Low backpressure with high plate counts, ideal for preparative applications</li><li>Low column bleed for low detector noise</li><li>Up and down scaling ensured beteween analytical RP-HPLC and preparative process chromatography</li><li>Recommended eluents: &nbsp;H₂O/ACN or H₂O/MeOH with up to 1 % TFA, FA or NaOH additive</li></ul><h4>Applications</h4><ul><li>Polar peptides, proteins or vitamins, hydrophobic amines</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

KNAUER AppliChrom® ABOA VivoSep SEC Columns

AppliChrom® SEC columns for water soluble (bio)polymers are multi hydrophilic layered SEC media for highest efficiency and low interaction.

AppliChrom® SEC columns for water soluble (bio)polymers<h4>Properties:</h4><ul><li>Multi hydrophilic layered SEC media for highest efficiency and low interaction</li><li>Available seperation ranges: from small molecules up to 5 500 kDa</li><li>Temperature stability: 10-90 °C</li><li>Stable between: pH 2–10</li><li>Pressure stability: up to 200 bar</li><li>Simple adaptation from HPLC to SEC with stainless steel instruments</li><li>Versatile tool for accurate protein molecular weight or size determination</li><li>Low column bleed for low detector noise</li><li>Increased lifetime of SEC columns through combination of proprietary particle and packing technology</li><li>Recommended eluents: H₂O, buffers</li></ul><h4>Applications</h4><ul><li>Water soluble proteins, humic substances</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

KNAUER AppliChrom® ABOA Cat-Phil SEC Columns

Interaction-free pure GPC & SEC base material with focus on polycationic, polyelectrolytic or funktional amine analytes

AppliChrom® SEC columns for neutral, anionic and additional cationic polymers<h4>Properties:</h4><ul><li>Interaction-free pure GPC &amp; SEC base material with focus on polycationic, polyelectrolytic or funktional amine analytes</li><li>No salt addition is needed to surpress surface adsorption</li><li>No ion exclusion phenomena</li><li>Possible to be used in universal calibration &amp; accurate molecular weight determination even for small polycationic molecules</li><li>Temperature stability between: 10–90 °C</li><li>Stable with: pH 2–10</li><li>Simple, reliable and robust GPC &amp; SEC calibration from dextrans, pullulans et al.</li><li>Low column bleed for low detector gain for improved refractive index, light scattering or viscosity detection</li><li>Large volume and optimized mass transfer for polymers with optimized resolution</li><li>Low cost due to long column lifetime - result of the combination of optimized particle and packing technology</li><li>Recommended eluents: H₂O, buffers</li></ul><h4>Applications</h4>Water soluble analytes like:<ul><li>polycations, polyamines (chitosanes), polyethylenoxides, polysaccharides, polyanions (heparins, pectins), polyethylene oxide (PEO), polyethylene glycol (PEG), Ppolyethyleneimins (PEI), polyvinylimidazole</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

KNAUER AppliChrom® ABOA StyDiViBe GPC Columns

Organic polystyrene-divinylbenzene copolymer base material with high porosity for high resolution

AppliChrom® GPC columns for GPC analysis of organic molecules with THF, toluene, chloroform<h4>Properties:</h4><ul><li>Organic polystyrene-divinylbenzene copolymer base material with high porosity for high resolution</li><li>High pressure stability: up to 150 bar</li><li>Temperature stable: between 10-145 °C</li><li>GPC range: from 0.1 up to 50 000 kDa</li><li>Low column bleed for low detector noise</li><li>High purity to eliminate adsorptive effects and combine pure GPC with long lifetime</li><li>Large calibration ranges for several decades due to the unique process of BPT technology</li><li>Range of individual porosities that can be used individually or in combination</li><li>Optimized for: 1 ml/min flow rate for 8 mm ID columns</li><li>High level of reproducibility and peak precision due to the advanced packing procedure</li><li>Recommended eluents: THF, Toluene, CHCl₃, dichlorbenzene, hexane/EtOAc (10:90, V:V)</li></ul><img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_Sty_Di_Vi_Be_P_Molecular_sizes_range_ca9a682d2e.jpg" alt="KNAUER: AppliChrom® ABOA StyDiViBe-P - Molecular sizes range" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_Sty_Di_Vi_Be_P_Molecular_sizes_range_ca9a682d2e.jpg 235w," sizes="100vw" width="1072" height="712"><h4>Applications</h4>Hydrophobic oligomers or polymers like:<ul><li>PVC, PMMA, polystyrene, epoxy resins, polyesters, bisphenol A resins</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

KNAUER AppliChrom® ABOA DMAc-Phil GPC Columns

Organic polymer base material with high porosity for high resolution

AppliChrom® GPC columns for organic GPC analyses in DMAc or DMF<h4>Properties:</h4><ul><li>Organic polymer base material with high porosity for high resolution</li><li>Wide range of porosities and particle sizes</li><li>Pressure stability: up to 150 bar</li><li>Stable between: 35-145 °C</li><li>Excellent reproducibility and resolution due to the advanced packing procedure</li><li>High purity to eliminate adsorptive effects and combine pure GPC with long lifetime</li><li>GPC range from: 100-1 000 000 Da</li><li>Optimal for: 0.5 ml/min flow rates with 8 mm ID colums</li><li>Recommended eluents: DMAc, DMF, NMP, LiBr additive</li></ul><h4>Applications</h4>Slightly polar analytes like:<ul><li>PMMA, polyacryl nitril (PAN), acrylnitrile butadiene styrene (ABS), cellulose, and all DMF and DMAc soluble polymers</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

KNAUER AppliChrom® ABOA DMSO-Phil GPC Columns

AppliChrom® DMSO-PHIL optimized for DMSO-GPC applications from an interaction-free pure GPC base material

AppliChrom® DMSO-PHIL optimized for DMSO-GPC applications<h4>Properties:</h4><ul><li>Interaction-free pure GPC base material</li><li>Temperature stabel between: 40-90 °C (145 °C) depending on application</li><li>Simple, reliable and robust GPC &amp; SEC calibration from dextrans, pullulans et al.</li><li>Low column bleed for low detector gain for improved refractive index, light scattering or viscosity detection</li><li>12 µm particle technology for low back pressure</li><li>Tolerates traces of water and NaNO₃ additve</li><li>Large volume and optimized mass transfer for polymers with optimized resolution</li><li>Low cost due to long column lifetime - result of the combination of optimized particle and packing technology</li><li>Recommended eluents: DMSO, 0.075 M NaNO₃</li></ul><h4>Applications</h4>Polar, not water soluble oligomers or polymers like:<ul><li>polysaccharides, lignin, amylose, starch, humic acids, polyvenyl pyridin, PNIPA, polyvinyl alcohol (PVA), melamin-urea-formaldehyd resin (MUF) or urea-formaldehyd resin (UF)</li></ul><h3>GPC &amp; SEC Columns</h3>GPC &amp; SEC systems offer solutions for various applications and laboratoriesGel permeation chromatography (GPC) and size exclusion chromatography (SEC) separate analytes by size using special columns with a porous matrix. The basic separation principle is based on the fact that smaller molecules penetrate these pores more strongly and therefore move more slowly through the matrix than larger molecules. GPC/SEC is often used as gentle and powerful purification technique or for quality control in research and development. Typical target molecules are polymers, dissolved in organic solvents for GPC, and macro biomolecules like proteins, antibodies or polysaccharides, dissolved in aqueous eluents for SEC.Separation is facilitated by selecting optimal particle and pore sizes. Therefore we offer a wide range of pore sizes (35, 100, 150, 250, 350, 500, 1000, 1500, 10E5, 10E6, 10E7 Å) and several particle sizes (5, 7, 10, 12, 20 µm) as a choice to customize for every application task.<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Size_Exclusion_principle_2a432edcc1.webp" alt="KNAUER: Size Exclusion - principle" srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Size_Exclusion_principle_2a432edcc1.webp 228w," sizes="100vw" width="1024" height="700"><h3>KNAUER AppliChrom® ABOA columns for aqueous SEC, organic GPC, and special applications</h3><ul><li>AppliChrom® ABOA StyDiViBe Series GPC-columns for GPC analysis of organic molecules using THF, toluene, chloroform.</li><li>AppliChrom ABOA SuperOH-P Series for aqueous GPC/SEC-analysis of mainly neutral and anionic polymers like heparins, polysaccharides, PEO, PEG,....</li><li>AppliChrom® ABOA DMSO-Phil-P Series for DMSO GPC/SEC analysis (humic substances, UF/MUF-glue, p-NIPA, many polycondensates, protein from pea or leguminosae,...)</li><li>AppliChrom® ABOA DMAc-Phil-P Series for GPC/ SEC analysis in DMAc, DMF, NMP. Good for many medium polar substances, polyoxazolines, lignin,...</li><li>AppliChrom® ABOA Cat-Phil-P Series for aqueous GPC/SEC-analysis of special aminic and polycationic polymers like p-DADMAc, PEI/ polyethylenimin, chitosan, copolymers with polyaminofunctions, but also useful for polyanions or neutral polymers like heparin or PEO/PEG, dextran or pullulan.</li><li>Seperation Ranges: 100–50 000 000 Da</li></ul><h4>You decide between classical GPC/SEC columns with conventional mixed pore technology or AppliChrom® BPT technology:</h4>Separate oligomers and polymers with the new GPC media line from AppliChrom® BPT synthesis technology for large range, high resolution separations with increased accuracy in calibration (patent pending).<img src="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg" alt="KNAUER: AppliChrom® ABOA columns." srcset="https://storage.googleapis.com/labrulez-bucket-strapi-h3hsga3/thumbnail_KNAUER_Appli_Chrom_ABOA_columns_58d5d380f6.jpg 245w," sizes="100vw" width="1379" height="718">

Products from category HPLC columns focused on Consumables - page 21

Related content

Oligos Made Easy - Part 3: IP-RP

News from LabRulezLCMS Library - Week 08, 2026

Why Is It Necessary to Dry the SPE Sorbent Before Elution?